ページ1に含まれる内容の要旨
®
Contour
Cordless XT
Original Instructions
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
360º Carton Contents Safety Lock-off Switch Switch Lever Steady Handle Battery Pack Battery Charger Upper Shaft Guard Lower Shaft Instruction Manual Plant and Tree Guard Wheel IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct Telephone : 0844 844 4558 UK 1800 882 350 ROI FAX : 01325 302530 Safety WARNING. When using the product the safety rules must be
ページ3に含まれる内容の要旨
10. Do not charge the battery or use the unit in an explo- 7. Never fit metal cutting elements. sive or corrosive environment. Avoid areas where 8. Keep hands and feet away from the cutting means at all flammable liquids or gases are present to avoid cre- times and especially when switching on the motor. ating a fire or explosion. 9. Keep cutting head below waist level. 11. Do not attempt to repair the unit including the battery. 10. Do not lean over the trimmer guard whilst trimming or Nylon l
ページ4に含まれる内容の要旨
Assembly Instructions cont’ Safety Guard Assembly (D) & (E) D 2 E 1. Locate the safety guard (D1) over the cutting head (D2). Ensure the nylon line is fed through the hole in the safety guard as illustrated in fig D. 2. Push into location and turn safety guard in the direc- tion illustrated in Fig E, until a click is heard and the safety guard is securely locked in position. • ENSURE THE SAFETY GUARD IS SECURELY IN 1 PLACE BY ATTEMPTING TO TWIST GUARD. Charging the Battery Pack Initial Charging
ページ5に含まれる内容の要旨
How to trim and edge H J 2 • WARNING 2 • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. K Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. REMOVE THE BATTERY PACK BEFORE ATTEMPT- ING ANY MAINTENANCE OR ADJUSTMENT. • BEFORE USE Make sure that the cutting line is fed out. • Make sure motor is
ページ6に含まれる内容の要旨
Auto Line Feed System How the automatic line feed works (P) P 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will re- duce as the motor reaches full speed. • Make sure the motor is up to full speed before trim- ming or edging. 3. If the noise of the nylon li
ページ7に含まれる内容の要旨
Maintenance V • WARNING Remove the Battery Pack before attempting any main- tenance or adjustment. Cutting head continues to ro- tate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Product W After you have finished using your product, follow the pro- cedure below: 1. Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 2. Using a
ページ8に含まれる内容の要旨
Fault Finding Chart WARNING Remove the Battery Pack before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No ing? SEE “MANUAL LINE FEED” OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. SEE “CUT- OR cleat? TING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is the manual line feed wo
ページ9に含まれる内容の要旨
Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture within Failures not covered by guarantee the guarantee period, Husqvarna UK Ltd., through its Authorised * Replacing Nylon Line. Service Repairers will effect the repair or replacement to the cus- * Failures as a result of not reporting an initial fault. tomer free of charge providing: * Failures as a result of sudden impact. (a) The fault is reported directly to the Authorised Repairer. * Failures as a r
