ページ1に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 1
User Manual (Part 2)
5.8 GHz Expansion
Handset E560-1
For use with AT&T
model E5633/E5630/E5600
ページ2に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 2 You must charge the See pages 2-3 battery and register the STOP! for easy instructions. handset before use. For customer service or product Please also read information, visit our web site at Important Product www.telephones.att.com Information Enclosed in product package. or call 1-800-222-3111. Table of contents Before you begin........................................1 Parts checklist ...........................................
ページ3に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 3 Before you begin This cordless telephone PHONE. Move closer to the operates with the maximum base, then press PHONE to power allowed by the answer the call. Federal Communications If you move out of range Commission (FCC). Even during a phone conver- so, this handset and base sation, you might hear can communicate over only noise or interference.To a certain distance — which improve reception, move can vary with the locations clo
ページ4に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 4 Battery & charger installation After installation, place the handset in the charger and allow the bat- tery to charge for 12 hours before use.You can keep the battery charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 10 hours.Average talk time on a fully charged battery is about eight hours depending on environmental conditions, standby time is approx
ページ5に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 5 Registering the handset Enter base ID, then press SELECT. Before using a new E560-1 handset, you must register it with the E5633 / E5630 / E5600 ENTER BASE ID base. During registration, you must enter the 15-digit ID number of the telephone base. The Base ID is located on the bottom of the base unit. Follow the instructions provided with your new handset to register it for use with your telephone. The handset provided with your t
ページ6に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 6 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap) 4
ページ7に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 7 Quick reference guide For complete instructions, please refer to the manual provided with your E5633, E5630 or E5600 telephone. Handset Select/Menu Press to display menu, or to select V CID highlighted item from menu. Press to scroll down in menus. Press when phone is not in use to dis- ^ PHONE BOOK play Caller ID information . While enter- ing names, press to move the cursor to Press to scroll up in menus. the left. Press when
ページ8に含まれる内容の要旨
91-000183-010-000-E560-1 Manual ok.qxd 2/13/1950 7:21 PM Page 8 www.telephones.att.com Copyright © 2004 Advanced American Telephones.All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 12/04. 91-000183-010-000
