ページ1に含まれる内容の要旨
Installation/Operation
Frontload Washers
Metered Commercial
FLW1527C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 803447R1
www.comlaundry.com January 2010
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are factors which cannot be built into these washers. These factors MUST BE supplied
ページ4に含まれる内容の要旨
Safety Information.............................................................................. 3 Table of Explanation of Safety Messages........................................................... 3 Important Safety Instructions ............................................................... 3 Contents Installation........................................................................................... 5 Dimensions and Specifications...........................................................
ページ5に含まれる内容の要旨
Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you (Save These Instructions) will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific WARNING instructions. These precautions are intended for the personal safety of the operator, user, servicer, and To reduce the risk of fire, electric shock, those maintaining the machine. serious injury or death to persons when using your wash
ページ6に含まれる内容の要旨
Safety Information 11. Do not repair or replace any part of the washer, or 20. Be sure water connections have a shut-off valve attempt any servicing unless specifically and that fill hose connections are tight. CLOSE recommended in the user-maintenance the shut-off valves at the end of each wash day. instructions or in published user-repair 21. Loading door MUST BE CLOSED any time the instructions that you understand and have the washer is to fill, tumble or spin. DO NOT bypass skills to c
ページ7に含まれる内容の要旨
Installation Dimensions and Specifications 5.1 cm (2 in.) 61.0 cm (24 in.) 33.3 cm (13.1 in.) 71.1 cm (28 in.) 68.3 cm (26.9 in.) 5.1 cm FLW2192N (2 in.) 3.8 cm (1.5 in.) COIN MODELS FLW2192N 61.0 cm (24 in.) 33.3 cm (13.1 in.) 71.1 cm (28 in.) 68.3 cm (26.9 in.) 5.1 cm (2 in.) 3.8 cm (1.5 in.) FLW2249N CENTRAL PAY MODELS FLW2249N 803447 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 104.6 cm (41.2 in.) 110.7 cm (43.6 in.) 79 cm (31.1 in.) 79 cm (31.1 in.) 75.1 cm (29.6 i
ページ8に含まれる内容の要旨
Installation Central Pay Models Before You Start The machine is shipped from the factory with the Tools Electronic Control Diagnostic Harness Assembly For most installations, the basic tools you will need unplugged. To avoid unauthorized manual are: programming or vending perform the following steps. 1. Open service door. Refer to Figure 2. 1 3 2 2. Locate diagnostic harness on electronic control. 4 3. Plug connectors for “white/black” wire and “red/ blue” wire together. 1 5 D074I 1 Wrench 2
ページ9に含まれる内容の要旨
Installation Step 2: Connect Fill Hoses Installing the Washer Step 1: Position Washer Near Installation WARNING Area Under certain conditions, hydrogen gas Move washer so that it is within 1.2 meters (4 feet) of may be produced in a hot water system the desired area of installation. that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If NOTE: For best performance and to minimize the hot water system has not been used vibration or movement, install washer on a solid,
ページ10に含まれる内容の要旨
Installation Turn on the water supply faucets and flush the lines for IMPORTANT: Hoses and other natural rubber approximately two minutes to remove any foreign parts deteriorate after extended use. Hoses may materials that could clog the screens in the water develop cracks, blisters or material wear from the mixing valve. temperature and constant high pressure they are subjected to. NOTE: When installing in newly constructed or renovated building, it is very important to flush the All hoses
ページ11に含まれる内容の要旨
Installation Risers Risers (or air cushions) may have to be installed if the 1 pipes knock or pound when flow of water stops. The risers are more efficient when installed as close as possible to the water supply faucets (refer to Figure 6). 1 2 FLW1982N W005I W005I 1 Shipping Tape 1 Risers (Air Cushions) 2 Water Supply Faucets Figure 7 Standpipe Installation Figure 6 Place the drain hose into the standpipe. Step 3: Connect Drain Hose to Drain Remove the beaded tie-down strap from accessor
ページ12に含まれる内容の要旨
Installation Step 4: Position and Level the Washer Tighten the locknuts securely against the washer base. If the locknuts are not tight, washer will move out of position during operation. WARNING NOTE: DO NOT slide washer across floor if the Washers elevated above floor level must leveling legs have been extended, as legs and base be anchored to that elevated surface, could become damaged. base or platform. The material used to elevate the washer should also be Remove rubber feet from acc
ページ13に含まれる内容の要旨
Installation Step 5: Remove the Shock Sleeves and Step 6: Wipe Out Inside of Wash Drum Shipping Brace Before using washer for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp Remove front access panel by removing the two screws cloth to remove shipping dust from inside wash drum. at the bottom of the panel. Remove the five bolts and lockwashers from shipping brace with a wrench and remove brace. Refer to Figure 10. Four bolts are located on the washe
ページ14に含まれる内容の要旨
Installation Step 7: Connect the Washer to Electrical Power Electrical Requirements 2 3 1 NOTE: The wiring diagram is located in the control cabinet. 120±12 0 V.A.C. V.A.C. NOTE: Refer to the washer nameplate on the rear cabinet panel for proper voltage and Hertz the washer is designed to operate on. 120±12 V.A.C. 5 4 WARNING To reduce the risk of fire, electric shock, Standard 120 Volt, 60 Hertz serious injury or death, all wiring and 3-Wire Effectively Earthed Circuit grounding MUST
ページ15に含まれる内容の要旨
Installation 240 Volt, 50 Hertz with 3-Prong Earthing Plug 220 Volt, 60 Hertz without Plug The washer is designed to be operated on a separate The washer is designed to be operated on a separate branch, polarized, three-wire, effectively earthed, branch, polarized, three-wire effectively earthed, 240 Volt, 50 Hertz, AC (alternating current) circuit 220 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 ampere fuse, equivalent fusetron or protected by a 15 ampere fuse, equivale
ページ16に含まれる内容の要旨
Installation Connecting to Central Pay System 1 IMPORTANT: Any central pay device and related installation wiring that is connected to the washer must maintain the Electromagnetic Compatibility (EMC) of the washer in order to comply with the appropriate national EMC regulatory requirements. The central pay device and related wiring, as a minimum, must meet the emission requirements of EN55014-1 and the immunity requirements of EN55014-2. Start Pulse Input Wiring Connections Use 511478 Re
ページ17に含まれる内容の要旨
Operation Step 2: Close Loading Door Operation Instructions Close loading door tightly. The washer will not IMPORTANT: Prior to first wash, use an all- operate with the loading door open. purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washtub. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Step 1: Load Laundry Load items loosely into wash drum (8.1 Kg maximum dr
ページ18に含まれる内容の要旨
Operation Step 3: Add Laundry Supplies Step 4: Set Fabric Selector/Wash Temperature Open dispenser drawer. Measure and add low sudsing, high efficiency (HE) detergent (1), bleach (2) and Push touchpad for HEAVY, NORMAL, PERM fabric softener (3) to the dispenser drawer (refer to PRESS or DELICATES cycle. Light indicates Figure 17). Close dispenser drawer. selection. IMPORTANT: If using non-HE detergent, avoid NOTE: Changes can be made to Fabric Selector oversudsing by using 1/2 of the det
ページ19に含まれる内容の要旨
Operation Step 6: Start Washer Indicator Lights After vend price has been satisfied, push the START WASH pad. DOOR MUST BE CLOSED TO START WASH is lit at the beginning of a wash cycle and will WASHER. remain lit until the wash cycle is complete. RINSE RINSE is lit at the beginning of all RINSE cycles and will remain lit until the rinse cycle is complete. SPIN SPIN is lit for all spin cycles. DOOR LOCKED DOOR LOCKED is lit whenever the door is locked. The door cannot be opened when this ligh
ページ20に含まれる内容の要旨
Maintenance Replacing Hoses User-Maintenance Instructions Hoses and other natural rubber parts deteriorate after Lubrication extended use. Hoses may develop cracks, blisters or All moving parts are sealed in a permanent supply of material wear from the temperature and constant high lubricant or are equipped with oilless bearings. pressure they are subjected to. Additional lubrication will not be necessary. All hoses should be checked on a monthly basis for Do not lubricate the door hinge. I
