ページ1に含まれる内容の要旨
3-232-392-13 (1)
Cordless
Telephone
US
Operating Instructions
Hearing-Aid Compatible
SPP-S2720
©2001 Sony Corporation
ページ2に含まれる内容の要旨
Caution IMPORTANT You are cautioned that any changes or modifications not expressly approved in this SAFETY manual could void your authority to operate this equipment. INSTRUCTIONS Privacy of communications may not be ensured when using this phone. When using your telephone equipment, basic safety precautions Note should always be followed to reduce the risk of fire, electric shock and This equipment has been tested and found to comply with the limits for a Class B digital injury to persons, inc
ページ3に含まれる内容の要旨
6. The telephone company may make INFORMATION FOR FCC changes to it’s facilities, equipment, REGURATION CLAIM operations or procedures that could affect the operation of the equipment. 1. This equipment complies with Part 15 and Part 68 of the FCC rules for the If this happens the telephone company will provide advance notice United States. On the bottom of this equipment is a label that contains, so you can make the necessary modifications to maintain among other information, the FCC certific
ページ4に含まれる内容の要旨
Precaución IMPORTANTES Se le advierte que cualquier cambio o modificación no aprobado expresamente en el INSTRUCCIONES presente manual podría anular su autorización para operar este equipo. DE SEGURIDAD El secreto de las comunicaciones puede no asegurarse cuando utilice este teléfono. A fin de reducir el riesgo de incendio, descarga eléctrica y Nota lesiones a las personas cuando usted Este equipo se ha sometido a pruebas y se ha determinado que cumple los límites para un use su equipo telefónic
ページ5に含まれる内容の要旨
6. La compañía telefónica puede realizar INFORMACIÓN PARA LA cambios en sus instalaciones, equipos, DEMANDA DE LA operaciones, o procedimientos que REGLAMENTACIÓN DE LA FCC pueden afectar la operación del equipo. Cuando suceda esto, la 1. Este equipo cumple con la Parte 15 y compañía telefónica le avisará con la Parte 68 de las reglas de la FCC antelación para que pueda realizar las para EE.UU. En la base de este modificaciones necesarias a fin de equipo hay una etiqueta que contiene, mantener
ページ6に含まれる内容の要旨
Table of contents Getting Started 46 Locating the handset 47 Switching the phones during a 8 Welcome call 9 Read this first 10 Step 1: Checking the package Intercom Operation contents 11 Step 2: Setting up the base unit 48 Talking between the phones – Intercom – Walkie-Talkie 14 Step 3: Preparing the battery function pack 49 Transferring a call 16 Step 4: Choosing the dialing mode 17 Step 5: Entering the area code Caller ID Features 21 Setting up the EZ Access function 50 Understanding the C
ページ7に含まれる内容の要旨
Additional Information 61 Carrying the cordless handset by the belt clip 62 Notes on power sources 63 Maintenance 64 Troubleshooting 68 Specifications 69 Index Back cover LIMITED WARRANTY US Table of contents 7
ページ8に含まれる内容の要旨
Getting Started Welcome Thank you for purchasing Sony QuadraStation 2.4! The phone systems can be expanded to a total of four cordless handsets and realizes the Intercom conversation between a couple of cordless handsets (walkie-talkie function). First, read the followings. • The system includes a cordless handset. If you utilize the walkie- talkie feature, it is necessary to purchase the SPP-H273 Sony cordless handset used for the QuadraStation 2.4 exclusively. • Be sure to register the additio
ページ9に含まれる内容の要旨
Getting Started Read this first Before you use your phone, you must first set it up. Here’s a quick way to set up your phone: Steps 1 to 5. Step 1 (page 10) First, unpack the phone and the supplied accessories. Step 2 (pages 11 to 13) You need to do two things to set up the base unit, including finding the best location for the base unit. Step 3 (pages 14 to 15) Base unit Insert the battery pack into the cordless handset and charge it for more than 12 hours. Step 4 (page 16) Choose an appro
ページ10に含まれる内容の要旨
Step 1 Checking the package contents Make sure you have received the following items in the package. If anything is missing, contact your local Sony dealer. AC power adaptor (AC-T46) Base unit Cordless handset Telephone Rechargeable line cord battery pack (BP-T38) US Getting Started 10
ページ11に含まれる内容の要旨
Getting Started Step 2 Setting up the base unit Do the following steps: • Choose the best location • Connect the base unit Choose the best location Where you place the base unit affects the reception quality of the cordless handset. Away from noise sources such as a window by a street with heavy traffic Away from television sets and other Away from heat sources, such as radiators, electronic equipment airducts, and sunlight Away from a microwave oven Away from excessive moisture, extremely low
ページ12に含まれる内容の要旨
Step 2: Setting up the base unit (continued) Connect the base unit 3 Hook the cord. 2 To an AC outlet To DC IN 9V To LINE AC power adaptor (supplied AC-T46) Telephone line cord 1 To a telephone (supplied) outlet 1 Connect the telephone line cord to the LINE jack and to a telephone outlet. 2 Connect the AC power adaptor to the DC IN 9V jack and to an AC outlet. 3 Raise the antenna. Make sure it points towards the ceiling. US Getting Started 12
ページ13に含まれる内容の要旨
Getting Started Notes • Use only the supplied AC-T46 AC power adaptor. Polarity of the plug Do not use any other AC power adaptor. • Connect the AC power adaptor to a continuous power supply. • Place the base unit close to the AC outlet so that you can unplug the AC power adaptor easily. Tip Modular If your telephone outlet is not modular, contact your telephone service company for assistance. US Getting Started 13 + –
ページ14に含まれる内容の要旨
Step 3 Preparing the battery pack Charge the battery pack for more than 12 hours before you start using your cordless handset. 1 Slide open the battery compartment lid of the cordless handset. BP-T38 2 Connect the battery connector with correct polarity (black wire Red goes on lower side and red wire goes on upper side). Black Hook 3 Hook the cords and insert the battery pack. Then close the lid. 4 Place the cordless handset on the base unit. The CHARGE lamp on the base unit lights up and “HANDS
ページ15に含まれる内容の要旨
Getting Started About the station number When you start charging the battery, “HANDSET 1” HANDSET 1 appears on the display of the cordless handset. This shows the ID number for each cordless handset and base unit of the system, called “station number.” The station NEW OLD MASSAGE RING OFF number of the base unit is set to 0 and that of the cordless handset (supplied with the base unit) is set to 1 at the factory. The station number of the cordless handset newly added to the system will be one of
ページ16に含まれる内容の要旨
Step 4 Choosing the dialing mode For the telephone to work properly, select an appropriate dialing mode (tone or pulse). When you set the dialing mode with the cordless handset, make sure the other cordless handsets* are not in use before you start the setting. You cannot set the dialing mode while the system is in use. * If the system includes any other additional cordless handsets. 1 Press (PGM). 2 Press (*TONE). You hear a confirmation beep. DIAL MODE 1:TONE 2:PULSE NEW OLD MASSAGE RING OFF 3
ページ17に含まれる内容の要旨
Getting Started Step 5 Entering the area code When you use this phone for the first time, or move to an area that has a different area code, you must enter the area code. Otherwise, you cannot use some functions of this phone and the Caller ID functions. This is also necessary because the phone must be able to select an area code to properly dial a call from the Caller ID list. Depending on your region, enter the 3-digit area code as follows: Case 1. If 7-digit dialing (no area code) is accepted
ページ18に含まれる内容の要旨
Step 5: Entering the area code (continued) 4 Enter the three digits of your home area code using the dialing keys. 5 Press (PGM). You hear a long confirmation beep. Notes • If the home area code is already entered, it appears on the display in step 2. To enter a different home area code, see “To change the home area code” below. • Do not allow more than 60 seconds to elapse during the operation procedure. • If the area code has not been entered, calling back from the Caller ID list and storing t
ページ19に含まれる内容の要旨
Getting Started To enter the local area code (For 10 digits phone numbers users) If a call matches one of the local area codes you entered, the phone number will be registered with 10 digits in the Caller ID list (area code + number). If a call does not match one of the local area codes you entered, the phone number will be registered with 11 digits in the Caller ID list (1 + area code + number). Some regions of the country allow you to have more than one local area code. (Up to five local area
ページ20に含まれる内容の要旨
Step 5: Entering the area code (continued) To change the local area code 1 Perform steps 1 to 3 on page 19. The current local area code appears on the display. 2 Press (ERASE) to erase the current local area code. 3 Enter a new local area code using the dialing keys. 4 Press (PGM). You hear a long confirmation beep. To erase the local area code You can erase the local area code. Perform steps 1 and 2 avobe, then press (PGM). The local area code will be erased, and you hear a long confirmation be
