ページ1に含まれる内容の要旨
Operating and Installation
Instructions
Ceramic Combiset
CS 1112
CS 1122
en-US
To prevent accidents and
appliance damage,
read these instructions
before
installation or use. M.-Nr. 07 346 400
ページ2に含まれる内容の要旨
Contents IMPORTANT SAFETY INSTRUCTIONS.................................3 Description of the combiset .........................................7 CS 1112..........................................................7 CS 1122..........................................................8 Before using for the first time........................................9 Clean the combiset .................................................9 How the burners work.............................................10 Use .......
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Children WARNING- When using your Children should not be left appliance follow basic unattended in an area where the precautions, including the appliance is in use. Never allow following: children to sit or stand on any part of the appliance. Read all instructions before Caution: Do not store items of interest installation or use to prevent to children in cabinets above the injury and appliance damage. appliance. Children climbing on the appliance to reach these i
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Technical safety Do not operate any appliance with a damaged cord or plug, or if the Installation, repair and maintenance appliance has been damaged in any work should be performed by a Miele manner. Contact Miele’s Technical authorized service technician. Work by Service Department. unqualified persons could be dangerous and may void the warranty. Under no circumstances open the outer casing of the appliance. Be sure your appliance is properly installed and
ページ5に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Safety Never use the appliance to heat a room. Due to the high temperatures DO NOT TOUCH THE COOKING radiated, objects left near the appliance AREA OR THE VICINITY AROUND THE could catch fire. COOKING AREA - During operation, the cooking area and its surroundings Do not use the appliance until it has will get hot and can cause burns. When been properly installed in the the combiset is shut off, the surface countertop. may remain hot enough to cause harm Do not
ページ6に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Be careful not to drop anything on To prevent burns and breathing the ceramic surface of the combiset. difficulty, allow the combiset to cool Even lightweight objects may cause before cleaning. Some cleaners may damage. produce toxic fumes if applied to a hot surface. Use the proper pan size. Select cookware with flat bottoms large Keep the combiset clean. Salt, enough to cover the heating element. sugar, and grit can cause scratches. Using undersized cookwa
ページ7に含まれる内容の要旨
Description of the combiset CS 1112 Variable burner : Control knobs for the burners: 4" or 7" (100 mm or 180 mm) - Standard burner (front) Power: 700 W or 1800 W Variable burner (rear) Standard burner : 11 5 / " (145 mm) - 16 Power: 1200 W Indicators Burner indicators Display On/Off indicator Symbol for the outer-ring of the variable burner "Residual Heat" indicator 7
ページ8に含まれる内容の要旨
Description of the combiset CS 1122 Extended burner Control knobs for the burners: 7 7" or 7" x 10 / " 16 Standard burner (front) (180 mm or 180 mm x 265 mm) - Power: 1500 W / 2400 W Extended burner (rear) Standard burner 11 5 / " (145 mm) - 16 Power: 1200 W Burner indicators Indicators Display On/Off indicator Extended burner indicator "Residual Heat" indicator 8
ページ9に含まれる内容の要旨
Before using for the first time Clean the combiset Heat the combiset Before using for the first time, clean Metal components of the appliance the appliance with a damp cloth and have a protective coating which may dry with a soft cloth. give off a slight odor the first time the appliance is heated. The smell will dissipate after a short Do not use liquid dish soap to clean time and does not indicate a faulty the combiset, this may cause connection or appliance defect. permanent blue discolorat
ページ10に含まれる内容の要旨
How the burners work One-ring burners use one heating strip, One-ring burner and two-ring burners and grill zones use two heating strips. Depending on the model, the heating strips may be separated by a certain distance. See the illustrations. Every burner is equipped with overheat protection (inside temperature limiter), to prevent the glass ceramic combiset from overheating (see the section on "Overheat protection"). Overheating protection When you select a power setting, the Heating strip
ページ11に含まれる内容の要旨
Use Turning a burner On/Off Turning on the second ring on a Variable/Extended burner To turn a burner on, press the control knob down and turn it clockwise Press the control knob down and turn to the desired setting. it clockwise past "12" to the symbol. Then turn the control knob counterclockwise to the desired setting. Turning off the burner will also turn off the second ring. When the cooking zone is turned back on again, only the To turn a burner off, turn the control inside ring
ページ12に含まれる内容の要旨
Use Residual Heat Indicator When a cooking zone is switched on, the On/Off indicator will light followed by the residual heat indicator. When the cooking zone is switched off, the On/Off indicator goes out. The residual heat indicator will turn off once the cooking zone is safe to the touch. Do not touch the burner or rest any objects on the combiset when the residual heat indicator is on. Danger of burns! 12
ページ13に含まれる内容の要旨
Use Settings Use for Power level* Melt butter, chocolate, etc. 1-2 Dissolving gelatine Prepare yogurt Warming small quantities of food/liquid 1-3 Keeping delicate dishes warm Cooking rice, Thawing frozen vegetables Warming liquid or half-set foods 3-5 Thickening sauces, e.g., hollandaise sauce Cooking rice pudding Defrosting frozen foods 4-6 Steaming vegetables, fish, etc. Cooking pasta, soups, etc. Steaming grains Boiling and continued cooking of large quantities of food 7 Gently sautéing fish,
ページ14に含まれる内容の要旨
Use Overheat protection Each cooking zone is equipped with a temperature limiter. This feature automatically turns off the heating element before the glass ceramic becomes too hot. Once the ceramic surface has cooled to a safe temperature the heating element will automatically turn back on. The overheat protection may be activated by: – turning on a burner without putting a pan on it. – heating an empty pan. – an uneven pan not sitting evenly on the burner. – the pan not conducting heat properly
ページ15に含まれる内容の要旨
Selecting cookware Following these tips will allow you to Pots and pans make the most of your ceramic Special cookware is not required, but combiset. as is true with all types of cooking appliances, the better the cookware, The cooking surface the better the performance. The ceramic combiset is made of an extremely hard and durable material. The surface is scratch resistant, not scratch proof. Avoid using cookware with ridged bottoms. Ridged pots with dirty or chipped enamel bottoms may – For th
ページ16に含まれる内容の要旨
Selecting cookware Copper bottom and aluminum pans may leave a residue on the combiset in the form of metallic lines. This is normal. These lines can be removed using a non-abrasive ceramic combiset cleaner or a shielded scraper blade. Be sure to clean the combiset after each use. Each time this residue is allowed to melt it becomes harder to remove and may mar the appearance of the combiset. Let the combiset cool before cleaning. Cast iron, glass or stoneware should not be used because they hav
ページ17に含まれる内容の要旨
Cleaning and care Do not use a steam cleaner to clean Clean any spills immediately before this appliance. Steam could they become difficult to remove. penetrate electrical components and cause a short circuit. Pressurized Clean the appliance regularly, steam could cause permanent preferably after each use. Allow the damage to the surface. appliance to cool before cleaning. Do not use any sharp pointed Ceramic surfaces objects which could damage the Wipe off any soiling using a damp seal betwee
ページ18に含まれる内容の要旨
Cleaning and care Stainless steel Clean stainless steel surfaces with warm water and liquid dish soap applied with a non-abrasive sponge and then wipe dry with a soft cloth. Soak baked or hardened spills first to loosen them. Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner (available from Miele). To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure. Do not use stainless steel cleaner on or around th
ページ19に含まれる内容の要旨
Frequently asked questions Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the appliance does not heat up after it is turned on? Possible fault Solution The circuit breaker has tripped. Check whether a fuse is blown. If the problem persists contact Miele. What if a heating element turns off then on again? Possible fault Solution The overheating protection
ページ20に含まれる内容の要旨
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. Adhere rating label sticker supplied with the appliance below. 20
