ページ1に含まれる内容の要旨
GAS HOB
ZGG 659
INSTRUCTION BOOKLET
IL
ページ2に含まれる内容の要旨
Important Safety Information You MUST read these warnings carefully before installing or using the appliance. Installation This appliance must be installed by qualified Ensure the control knobs are in the ‘OFF’ personnel, according to the manufacturer’s position when not in use. instructions and to the rules in force. When using other electrical appliances, ensure Remove all packaging before using the the cable does not come into contact with the appliance. hot surfaces of the cooking applia
ページ3に含まれる内容の要旨
Contents For the User For the Installer Description of the Appliance Page 4 Engineers Technical Data Page 7 Operation Page 5 Installation Page 8 Maintenance and Cleaning Page 6 Gas Connection Page 8 Something Not Working? Page 7 Building in Page 9 Fitting the Hob to the Worktop Page 10 Electrical Connection Page 10 Commissioning Page 11 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instru
ページ4に含まれる内容の要旨
Description of the Appliance 3 5 6 7 1 8 4 2 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) INSTALLATION WHEN THE HOB IS FIRST Any gas installation must be carried out INSTALLED by qualified personnel, and in accordance Once the hob has been installed, it is with existing rules a
ページ5に含まれる内容の要旨
Operation Hob burners control knobs The symbols on the hob burners control knobs mean that: there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before FO 2295 putting a pan on the pan support. Fig. 1 A - Burner cap To light a burner: B - Ignition candle Push in the relevant knob and turn it anticlockwise to "maximum position". C - Thermocouple At the same time, keep the knob pushed down for about 5 seconds. This wil
ページ6に含まれる内容の要旨
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top and the aluminium frame using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregna
ページ7に含まれる内容の要旨
Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the burner cap and crown have been replaced correctly, e.g. after cleaning. The gas ring burns unevenly Check the main jet is not blocked and the burner c
ページ8に含まれる内容の要旨
510 470 55 min. Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/2" threaded elbow, an adjustable joint is fixed so that the washer (B) is fitted between the components as shown in figure 4. A drop of paint at both edges of the "L" joint (C) will e
ページ9に含まれる内容の要旨
Building in Building over a cupboard or Building over a kitchen unit with drawer oven If the hob is to be installed above a cupboard or If the hob is built into a kitchen unit with an oven drawer it will be necessary to fit a heat resistant underneath, the recess must have the dimensions board below the base of the hob on the underside shown in diagrams 2 and 3, and should also incor- of the work surface. porate suitable oven crosspiece supports to ansure an efficient cooling air circulation. Bu
ページ10に含まれる内容の要旨
Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge (see figure 6) of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near FO 2108 Fig. 6 the hob seeping into the cabinet below. 1) Remove the pan supports, the burners caps and crowns and turn the hob upside A down, taking care the ignition candles are not damaged in this operation. 2) Place the sealing gasket all around
ページ11に含まれる内容の要旨
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Fig. 8 Re-ignite the burner and set to MIN. By-pass screw Remove the control knob, insert a thin bladed screwd
