ページ1に含まれる内容の要旨
Electronic Calculator Operating Manual
Calculatrice Electronique Manuel du Fonctionnement
Calculador a Electronica Manual de Instrucciones
Model
Modèles
Modelos
1530-6
1560-6
1570-6
- 1 -
ページ2に含まれる内容の要旨
Preface Congratulations on your choice of a Victor electronic calculator. Careful design, quality materials, painstaking workmanship, and advanced research and production facilities have given you a calculator that, with proper care, will provide years of trouble-free service. To assure future optimum performance, ask your Victor representative about low-cost protection offered by Victor’s Extended Guarantee Protection Program. (To order see enclosed form on Page 68) This operating
ページ3に含まれる内容の要旨
BEFORE TURNING ON - Please remove the shipping-cushion placed on the ribbon and check the rating label on the bottom to see if the rated voltage corresponds to the local voltage before plugging in the AC cord. Note: Ribbon cushion is located under printer cover. ACTIVATE BACKUP BATTERY Before start using the calculator, please remove the insulation paper below the backup battery. 1. Turn the AC power switch OFF and remove the battery compartment cover located on the bottom cas
ページ4に含まれる内容の要旨
REPLACING THE RIBBON Your calculator is shipped with a 2-color ribbon already in place. You do not need to install or change it before you begin using the calculator. When you have been using your calculator for some time, however, the print will gradually become faint, indicating that you should change the ribbon. To change the ribbon, follow these steps. 1. Remove paper roll, tearing paper at rear of calculator. Use the Paper Advance ( ↑) key to feed the remaining paper tape
ページ5に含まれる内容の要旨
HOW TO FEED THE PAPER TAPE 1. Put the new paper roll on the paper arm. 2. Insert the paper into the slot as indicated. 3. Depress the paper feed key. 4. Suitable paper roll: Width: max. 58mm (2.25”) Diameter: max. 50mm (1.97”) Paper: Normal paper (45kg/1000 sheets/788 x 1091 mm) BATTERY REPLACEMENT 1. Turn the AC power switch off 2. Remove - the battery compartment cover located on the calculator bottom case. 3. Remove
ページ6に含まれる内容の要旨
Model 1570-6 Keyboard Layout 1 2 3 4 5 6 10 11 12 13 14 15 9 8 7 20 23 26 28a 16 31 21 29 17 32 24 18 33 19 34 22 30 27 25 Model 1560-6 and 1530-6 Keyboard Layout 1 2 3 4 5 6 8 9 10 11 12 13 14 15 7 20 23 26 28b 16 31 21 29 17 32 24 18 33 19 34 22 27 30 25 - 6 -
ページ7に含まれる内容の要旨
KEYBOARD LAYOUT 1. Rounding Selector 19. Percentage 2. Print Switch 20. Division 3. Decimal Selector 21. Equal 4. Financial Calculation Switch 22. Multiplication 5. Sigma/Loan and FV Switch 23a. Clear / Clear Entry 6. Grand Total Switch 24. Time / Date Display 7. Paper Feed 25. Numeric Key Pad 8. Delta Percentage 26. Subtraction 9. Time/Date Calculation 27. Addition 10. Cost 28a. Memory II Selector 11. Sell 28b. Item Count 12. Margin 29. Subtotal / Date 13. Tax Rate Preset 30.
ページ8に含まれる内容の要旨
independent of the accumulator and the calculating register, it retains its value until you clear it with the Memory Total (MT) key. SLIDE SWITCH FEATURES This section illustrates and describes the mode switches you can use to control your calculator’s operation. 1. ↓ 5/4 ↑ Decimal Rounding Selector ↓ This causes automatic round down (truncation). 5/4 This setting causes automatic round off. If the last digit of the result that will be printed or printed/displayed upon
ページ9に含まれる内容の要旨
Tax 2 Key change to FV key Memory Total key change to Amount key Memory Minus key change to Interest key Memory Plus key change to Months key Memory Subtotal key change to Payment key Note: Cost-Sell-Margin is disabled when in this mode. 5. • ∑/Loan FV Sigma/Loan and Futre Value Switch F-Cal=Off • work as Sigma off ∑ work as Sigma on F-Cal = ON • work as Loan ∑ work as FV ∑ When the Sigma switch is in the “∑” position, the results of
ページ10に含まれる内容の要旨
(MM-DD-YYYY). In Date mode, MT key changes to Start Date key, M- key changes to End Date key, M+ key changes to Number of Days key and MS key changes to Compute key. 10. [COST] Cost Key Used to enter the Cost factor in a Gross Profit Margin calculation. 11. [SELL] Sell Key Used to enter the Selling price in a Gross Profit Margin calculation. 12. [MARGIN] Margin Key Used to enter the desired Margin in a Gross Profit Margin calculation. 13
ページ11に含まれる内容の要旨
you depress the =, %, M+, M-, X or ÷ key. Each divisor entry is retained as a constant (except M+ and M- entries) until you depress the X, ÷ or Clear. 21. [=] Equal Key To get the result in multiplication or division. 22. [X] Multiplication Key The multiplication key performs multiplication, automatic constant multiplication and intermediate sequential operations. It establishes the amount entered or the prervious printed or printed/displayed
ページ12に含まれる内容の要旨
Calculation on memory II by press Memory II key follow by plus, minus, subtotal or total key. 28b. [N] Item Count Key Model 1560-6 & 1530-6 Calculations with item count and/or averaging. Also used to set the N count to Gross or Net. 29. [# / S] Date / Subtotal Key # : It will print live entry as an identifier as an invoice number with “#” mark. S : It prints but does not
ページ13に含まれる内容の要旨
Months: If this key is pressed after 10-key input, it is means enter the value as Number of Months to settle the Loan. If Amount, Interest, and Payment are entered in prior, or modification is done on any of the three as above in prior, user can calculate / recalculate the Number of Months # of Days: Used to calculate two different dates. If days is not change sign that is calculate future date. If days is change sign that is calculate past date. 34. [MS / Payment/Compute] M
ページ14に含まれる内容の要旨
Troubleshooting Many problems such as no power, no key response tec. Can be resolved using the RESET button. Please follow these instructions: 1. Machine must be plugged in and ON, and in the PRINT mode. 2. Turn machine over so you can see the battery compartment. 3. Open the battery compartment and locate the RESET button located next to the silver battery. 4. Depress the RESET button; you will hear the machine cycle. If you do not hear nd the machine recycle, push the button a 2 ti
ページ15に含まれる内容の要旨
Application Examples Ejemplos de Applicacion Exemples d'Application English – Spanish – French 1. Backspace – Retroceso – Rappel Arriére Rounding Print Decimal F-Cal ∑ GT 5/4 P 4 . . . Problem Enter Display Paper Problema Apriete Desplegado Papel Problème Appuyer Sur Afficher Bande 5.4321 + 2.34567 = ? 5.4321 [+] 5.4321 5.4321 + 2.3457 [ →] 2.345 67 [+]
ページ16に含まれる内容の要旨
3. Addition & Subtraction – Adicion Y Sustraccion – Addition et Soustraction Rounding Print Decimal F-Cal ∑ GT 5/4 P F . . . Problem Enter Display Paper Problema Apriete Desplegado Papel Problème Appuyer Sur Afficher Bande 2 + 3.1415926 – 6=? 2 [+] 2. 2. + 3.1415926 [+] 5.1415926 3.1415926 + 6 [-] - 0.8584074 [T] - 0.8584074 6. −
ページ17に含まれる内容の要旨
5. Item Count Presetting – Preestableciendo el contador de partidas – Programmation du compteur d'articles Rounding Print Decimal F-Cal ∑ GT 5/4 P + . . . The Item Count is Programmable for Gross Count or Net Count Contador de Partidos es programmable para Contador bruto ó contador neto. La programmation du compteur d'articles peut être brute ou nette. Gross I
ページ18に含まれる内容の要旨
6. (A) Addition/Subtraction with Item Count in Gross Setting Adicion/Sustraccion con Contador de Partidas en Modo Bruto Addition/soustraction avec compteur brut d'item Rounding Print Decimal F-Cal ∑ GT 5/4 P + . . . Problem Enter Display Paper Problema Apriete Desplegado Papel Problème Appuyer Sur Afficher Bande 11.
ページ19に含まれる内容の要旨
6. (C) Item Count with Averaging Contador de partidas con promodio Moyenne avec compteur d'item Rounding Print Decimal F-Cal ∑ GT 5/4 P + . . . Problem Enter Display Paper Problema Apriete Desplegado Papel Problème Appuyer Sur Afficher Bande 123+456+789+987=? 123 [+] 1.23 1.23 + 456 [+] 5.79
ページ20に含まれる内容の要旨
B. Model 1530-6, 1560-6 Rounding Print Decimal F-Cal ∑ GT 5/4 P + . . GT Problem Enter Display Paper Problema Apriete Desplegado Papel Problème Appuyer Sur Afficher Bande 13.20 9.55 [C/CE] 0. 0. C 8.30
