Résumé du contenu de la page N° 1
Installation
Instructions
Instructions
d’installation
30″ Stainless Steel
Gas Cooktops
Natural Gas Model:
ZGU384N
LP Gas Model:
ZGU384L
Surfaces de cuisson
au gaz de acier
inoxydable de 30 po
(76 cm)
Modèle à gaz naturel :
ZGU384N
Modèle à gaz PL :
ZGU384L
La section française commence
à la page 19.
Questions?
Call 800.GE.CARES
or Visit our Website at:
www.monogram.com
Appelez le Centre de réponse 1.800.561.3344
ou visitez notre site Web à l’adresse :
www.electromenagersge.ca
31-10635-2
08-0
Résumé du contenu de la page N° 2
Safety Information BEFORE YOU BEGIN WARNING — Disconnect all electrical power at the main circuit breaker or fuse box Read these instructions completely and carefully. before installing. • IMPORTANT — Save these instructions for local inspector’s use. This cooktop has been design certified by Underwriters • IMPORTANT — Observe all governing Laboratories. You’ll find safety precautions in your codes and ordinances. Owner’s Manual. Read them carefully. • Note to Installer – Be sure to leave these
Résumé du contenu de la page N° 3
Safety Information ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper result in a hazardous condition. If there are no codes, voltage and frequency and connected to an your cooktop must be wired and fused to meet the individual, properly grounded branch circuit, protected requirements of the National Electrical Code, by a circuit breaker or fuse having amperage as noted ANSI/NFPA No. 70—Latest Edition. You can on the rating plate. get a copy by writing: We recommend you hav
Résumé du contenu de la page N° 4
Installation Preparation MODELS AVAILABLE ZGU384N 30″ natural gas cooktop ZGU384L 30″ LP gas cooktop These models are factory set for either natural gas or LP gas operation. Be sure to order the correct model for the installation situation. PARTS INCLUDED TOOLS YOU WILL NEED FOR INSTALLATION Pencil 2 Screws 2 Hold Regulator Down Brackets Saber Saw Phillips Head Screwdriver MATERIALS YOU MAY NEED Pipe Wrench Ruler or Straightedge Joint Pipe Fittings Shut Off Sealant Valve 1/8″ Drill Bit & Elec
Résumé du contenu de la page N° 5
Installation Preparation ADVANCE PLANNING INSTALLATION OPTIONS • Refer to “Installation Preparation” for Cooktop and ZVB30 Downdraft Vent Combination information on appropriate placement and Installation necessary clearances when planning These cooktops may be installed with a 30″ installation. Monogram Downdraft Vent, model ZVB30. • Avoid placing cabinetry directly above cooktop See page 12 for cutout and clearances. when possible. – The countertop must have a deep flat surface to • If cabinet
Résumé du contenu de la page N° 6
Installation Preparation PRE-INSTALLATION CHECKLIST 1. When preparing cooktop opening, make sure 3. Remove Installation Instructions from literature the inside of the cabinet and the cooktop do package and read them carefully before you not interfere with each other. (See section on begin. preparing the opening.) Be sure to place all literature, Owner’s Manual, 2. Slide the cooktop out of the end of the box. Installations, etc. in a safe place for future Remove packaging materials, grate boxes,
Résumé du contenu de la page N° 7
Installation Preparation DIMENSIONS AND CLEARANCES 1. Overall cooktop dimensions: 3. Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat 30-3/4″ (up to 200°F) generated by the cooktop. 21-5/8″ 21″ deep at 13″ max. center 3-3/4″ 30″ 30″ min. 18″ min. min. 2. Use a 30″ or wider base cabinet. • Cut the opening in the countertop. To ensure accuracy, it is best to make a template for the opening. Make sure the sides of the opening are parallel and the rear an
Résumé du contenu de la page N° 8
Installation Preparation POWER SUPPLY LOCATIONS Install a manual shut-off valve in the gas line in an easily accessible location outside the cooktop. Be Gas supply: sure you know how and where to shut off the gas These cooktops are shipped from the factory set supply to the cooktop. Install the electrical outlet for either natural gas or LP gas. Check to be sure 12″ below the countertop. you have the correct cooktop for the type of gas Electrical supply: being used. • The pressure regulator m
Résumé du contenu de la page N° 9
Installation Instructions 1 INSTALL THE COOKTOP 2 INSTALL PRESSURE REGULATOR (cont.) A. Remove the screws on the sides of the cooktop burner box. Use those screws to attach the side Burner Box mounting brackets. B. Insert the cooktop centered into the cutout opening. Make sure the front edge of the 90º Elbow countertop is parallel to the cooktop. Check clearances at the front, back and sides. OPTION: You can install a 90º elbow (not supplied) Cooktop onto the gas inlet and route the gas connec
Résumé du contenu de la page N° 10
Installation Instructions 4 ASSEMBLE BURNERS, 4 ASSEMBLE BURNERS, CHECK IGNITION CHECK IGNITION (cont.) The electrode of the electronic ignition system D. Check igniters. is positioned above the surface of the burner Operation of the electric igniters should base. Do not remove a burner cap or touch the be tested after the cooktop and supply line electrode of a burner while another is turned have been carefully checked for leaks and the on. Damage or electrical shock may occur. cooktop has b
Résumé du contenu de la page N° 11
Installation Instructions 4 ASSEMBLE BURNERS, OPERATION CHECKLIST CHECK IGNITION (cont.) 1. Make sure all controls are left in the OFF position. F. Turn on each burner. On LP models, flames should be blue in color but may have yellow 2. The serial plate for your cooktop is located tips. Natural gas models should have soft, blue on the bottom of the burner box. In addition to flames. The burner flames should not flutter or the model and serial numbers, it tells you the blow away from the burn
Résumé du contenu de la page N° 12
Installation Options COOKTOP INSTALLATION WITH A COOKTOP REQUIREMENTS 30″ MONOGRAM DOWNDRAFT VENT, The countertop must have a deep flat surface to MODEL ZVB30 accommodate the cooktop and vent. Countertops with a rolled front edge and backsplash will not The installation of the downdraft vent with provide the flat surface area required. this cooktop requires careful consideration. Both the cooktop and the vent must be installed • Review the illustration to determine the countertop according to
Résumé du contenu de la page N° 13
Installation Options COOKTOP INSTALLATION OVER A POWER SUPPLY: MONOGRAM WARMING DRAWER, If local codes permit, the cooktop and warming MODEL ZTD910 OR ZKD910 drawer may operate from the same 120V duplex outlet. Refer to installation instructions for details. These cooktops may be installed over a 30″ or 27″ Warming Drawer. Both the cooktop and the warming drawer must be installed according to each specific installation instruction. Install 2x4 or 2x2 anti-tip block against rear cabinet wall 9″
Résumé du contenu de la page N° 14
Installation Options COOKTOP INSTALLATION OVER A POWER SUPPLY 27″ OR 30″ MONOGRAM SINGLE OVEN, The oven requires a separate, properly grounded MODEL ZET1, ZEK938 OR ZET938 20 Amp, 3-wire 208 or 240 volt, 60 Hz power supply. The cooktop requires a separate 120V power supply. These cooktops may be installed over the See page 8. Where codes permit, the gas shut-off Monogram ZET1, ZEK938 or ZET938 single oven. valve may be located in an adjacent cabinet or Both the cooktop and the oven must be ins
Résumé du contenu de la page N° 15
Installation Convert Natural Gas Model ZGU384NSMSS to LP Gas Operation Instructions SAFETY INFORMATION 1 ADJUST THE REGULATOR The pressure regulator and burner orifices are set for A. Disconnect all electrical power, at the main circuit natural gas operation. breaker or fuse box. B. Shut off the gas supply to the cooktop by closing the To convert this cooktop from natural gas operation to manual shut-off valve. LP operation, the regulator and burner orifices must be converted. LP burner orifice
Résumé du contenu de la page N° 16
Installation Instructions for Natural to LP Gas Conversion 2 CHANGE BURNER ORIFICES (cont.) 3 ADJUST BURNER FLAMES IMPORTANT: Orifices must be located exactly as shown. A. Turn all burners on highest setting and check the flames. Carefully read and observe each orifice label for correct They should be blue in color and may have some yellow location. tipping at the ends of the flame when using LP gas. Foreign particles in the gas line may cause an orange The 34SL and SIMMER flame at first, but th
Résumé du contenu de la page N° 17
Installation Convert LP Gas Model ZGU384LSMSS to Natural Gas Operation Instructions SAFETY INFORMATION 1 ADJUST THE REGULATOR The pressure regulator and burner orifices are set for A. Disconnect all electrical power, at the main circuit Liquid Propane (LP) gas operation. breaker or fuse box. B. Shut off the gas supply to the cooktop by closing the To convert this cooktop from LP gas operation to manual shut-off valve. natural gas operation, the regulator and burner orifices must be converted. N
Résumé du contenu de la page N° 18
Installation Instructions for LP to Natural Gas Conversion 2 CHANGE BURNER ORIFICES (cont.) 3 ADJUST BURNER FLAMES IMPORTANT: Orifices must be located exactly as shown. A. Turn all burners on highest setting and check the flames. Carefully read and observe each orifice label for correct They should be blue (no yellow tipping) when using location. natural gas. Foreign particles in the gas line may cause an orange flame at first, but this will soon disappear. The 34SL and SIMMER B. Turn the cookto
Résumé du contenu de la page N° 19
La section Française Information de la sécurité AVANT DE COMMENCER POUR VOTRE SÉCURITÉ Avant de commencer, lisez attentivement la AVERTISSEMENT — totalité de ces instructions. Si vous ne suivez pas exactement les instructions de ce manuel, vous risquez d’occasionner un • IMPORTANT — Conservez ces incendie, une explosion ou une fuite de gaz, qui instructions pour votre inspecteur local. peuvent provoquer des dommages matériels, des blessures corporelles ou la mort. • IMPORTANT — Respectez toutes
Résumé du contenu de la page N° 20
Information de la sécurité BESOINS D’ÉLECTRICITÉ AVERTISSEMENT — Débranchez tout courant électrique au niveau du disjoncteur de Cet appareil ménager doit être livré avec le bon la maison ou de la boîte à fusibles avant d’installer. voltage et la bonne fréquence et branché à son propre circuit de dérivation bien mis à la terre, protégé par un disjoncteur ou un fusible qui ont l’ampérage noté sur la plaque minéralogique de La conception de votre table de cuisson a été votre appareil. approuvé par
