Résumé du contenu de la page N° 1
ENGLISH
OWNER’S MANUAL
LCD TOUCH MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
LCD TOUCH MONITOR MODELS
T1710B
T1910B
www.lg.com
Résumé du contenu de la page N° 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Résumé du contenu de la page N° 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Résumé du contenu de la page N° 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Résumé du contenu de la page N° 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Power Cord Owner's Manual/Cards 15-pin D-Sub Signal Cable USB Cable (To set it up, this signal cable may be attached to this product before shipping out.) Touch Driver CD NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to main
Résumé du contenu de la page N° 6
Basic Adjustments of the Stand After installing the monitor, adjust the angle as follows. Basic Adjustment 1. Adjust the angle of the panel as follows. How to adjust the angle of the panel Tilt Range : T1710B : 15˚ to 66˚ T1910B : 15˚ to 68˚ 15˚ 66˚(68˚) Push back the panel to the end, and use from the point that it automatically returns. Panel Stand Do not push the stand with basic adjustment to the direction of the panel. The product may fall down to hurt people, or cause product disorder o
Résumé du contenu de la page N° 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map 1 2 form to . A Connect D-sub Cable (PC) B Connect D-sub Cable (Mac) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Analog signal Power Cord D-sub Wall-outlet type Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high den
Résumé du contenu de la page N° 8
Connecting the Display To Use Touch Screen Install the Driver CD provided. 1) Insert Touch Screen Driver CD into PC CO-ROM. 2) After completing the driver installation, connect the USB cable for the touch screen. 3) Please refer to the Touch Screen CD provided separately for detail installations. * The software drivers support the following Microsoft Windows operating systems: Windows 2000, XP, VISTA(32bit, 64bit). NOTE When you lose Driver CD or want to update the program, please refer to htt
Résumé du contenu de la page N° 9
Control Panel Functions Front Panel Controls Control Function Use this button to enter or exit from the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKE
Résumé du contenu de la page N° 10
Control Panel Functions Control Function Use these buttons to select or adjust functions in the On Buttons Screen Display. For more information, refer to page A16. Use this button to select an icon in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display m
Résumé du contenu de la page N° 11
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Résumé du contenu de la page N° 12
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. (D-sub ) NOTE The order of icons may differ depending on the model (A11 to A16 ). A11
Résumé du contenu de la page N° 13
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display
Résumé du contenu de la page N° 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE To adjust the brightness of the screen. BRIGHTNESS To adjust the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR PRESET • sRGB: Set the screen color to fit the sRGB standard color specification. • 6500K:
Résumé du contenu de la page N° 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. To minimize any vertical bars or CLOCK stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. PHASE This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease SHARPNESS To adjust the clearness of the : I
Résumé du contenu de la page N° 16
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP To choose the language in which the LANGUAGE control names are displayed. OSD To adjust position of the OSD window POSITION on the screen. If the output of the video card is different WHITE BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provi
Résumé du contenu de la page N° 17
On Screen Display(OSD) Selection and Adjustment Select the button at the bottom of the monitor, then the OSD screen will appear. Menu Name Icons Sub-menu Name Main menu Sub menu Description This feature lets you easily select the best desired image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) USER The user can directly adjust ACE and RCM. You can
Résumé du contenu de la page N° 18
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving the mouse or pressing any key on the keyb
Résumé du contenu de la page N° 19
Troubleshooting Display image is incorrect Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Press the AUTO/SET button to automatically On the screen adjust your display image to the ideal setting. background, vertical If the results are unsatisfactory, decrease the bars or stripes are vert
Résumé du contenu de la page N° 20
Troubleshooting Display image is incorrect The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (Color Quality) at Control Panel --> Settings. The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Touch screen does not work. Did you install the
