Résumé du contenu de la page N° 1
AOC MONITOR
USER`S GUIDE
2436Swa
SAFETY INTRODUCTION…………………………………………………………….2
SETUP…………………………………………………………………………………….4
ADJUSTING…………….…………………………………………………...…………..7
DRIVER INSTALLATION GUIDE…………………….….…………………………15
PRODUCT INFORMATION………………………………………………………….22
TROUBLESHOOT……...………………………………………………………….…..24
| Page ١
Résumé du contenu de la page N° 2
SAFETY INTRODUCTION The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or
Résumé du contenu de la page N° 3
Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATE
Résumé du contenu de la page N° 4
SETUP Please setup or remove the base following the steps as below. | Page ۴
Résumé du contenu de la page N° 5
Setup: Remove: For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 20 °. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. | Page ۵
Résumé du contenu de la page N° 6
Cable Connections On Back of Monitor and Computer 1. Power 2. Analog (DB-15 VGA cable) 3.Audio To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3. Connect the audio cable to audio in port on the back of the monitor 4. Turn on your monitor and computer.
Résumé du contenu de la page N° 7
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this ure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the f the monitor. 4. Insert the 4 screws into the holes and tighten. 5. Reconnect the cables. Refer to the user's manual that came with the optional wa
Résumé du contenu de la page N° 8
4 Click Personalization 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. | Page ٨
Résumé du contenu de la page N° 9
For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. | Page ٩
Résumé du contenu de la page N° 10
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. | Page ١٠
Résumé du contenu de la page N° 11
HOTKEYS Power Press to turn on or turn off the monitor. 4:3 or wide / Up Press key to change the screen aspect ratio between standard 4 ：3format or Wide format. When the input resolution is wide format, the aspect ratio hotkey is disabled. When the main menu or sub-menu is active, the key functions as to select up or increase value. Auto / Down Auto configure hot key: When the OSD is closed, press Auto button to do auto configure. OSD SETTING
Résumé du contenu de la page N° 12
Eco mode ---DCR, Standard, Text, Internet, Game, Movie, Sports DCR Standard | Page ١٢
Résumé du contenu de la page N° 13
TEXT INTERNET Game | Page ١٣
Résumé du contenu de la page N° 14
Movie Sports Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as “On”, Contrast, Brightness, Eco mode and Gamma can not be adjusted. | Page ١۴
Résumé du contenu de la page N° 15
LED INDICATOR Status LED Color Full Power Mode Blue Active-off Mode Orange DRIVER INSTALLATION GUIDE Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Prope
Résumé du contenu de la page N° 16
Windows ME 1. Start Windows® Me 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select the 'Monitor' button, then click on 'Change...' button. 6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button. 7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then
Résumé du contenu de la page N° 17
4. Click on the 'Display' Item. 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button. Please follow the steps below. | Page ١٧
Résumé du contenu de la page N° 18
7. Click on the 'Driver' tab and then click on 'Update Driver...' button. 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. | Page ١٨
Résumé du contenu de la page N° 19
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F: (CD-ROM Drive). 11. Click on the 'Open' button, then click the 'OK' button. 12. Select your monitor model and click on the 'Next' button. - If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message, please click on the 'Continue Anyway' button. 13. Click on the 'Finish' button then the 'Close' button. 14. Click on
Résumé du contenu de la page N° 20
3. Click "Advanced Settings...". 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". 5. Click "Update Driver..." in the "Driver" tab. | Page ٢٠
