Résumé du contenu de la page N° 1
Touchmonitor User Guide
1528L 15-inch LCD Desktop Touchmonitor
Model ET1528L
Résumé du contenu de la page N° 2
User Guide 15-inch LCD Desktop 1528L Touchmonitor Revision B P/N E894354 ii
Résumé du contenu de la page N° 3
Copyright 2008 Tyco Electronics Corporation. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Tyco Electronics Corporation. Disclaimer The information in this document is subject to change without notice.
Résumé du contenu de la page N° 4
Warnings and Cautions Warning • Danger — Explosion hazard. Do not use in the presence of flammable anesthetics. • To prevent fire or shock hazards, do not immerse the unit in water or expose it to rain or moisture. • Do not use the unit with an extension cord receptacle or other outlets unless the prongs of the power cord can be fully inserted. • RISK OF ELECTRICAL SHOCK — DO NOT OPEN. To reduce the risk of electrical shock, DO NOT remove the back of the equipment or open the enclosure.
Résumé du contenu de la page N° 5
EMC Guidance Guidance and manufacturer’s declaration – electromagnetic emissions The 1528L is intended for use in the electromagnetic environment specified below. The customer or the user of the 1528L should assure that it is used in such an environment. Emissions test Compliance Electromagnetic environment – guidance RF emissions Group 1 The 1528L uses RF energy only for its internal function. Therefore, its RF emissions CISPR 11 are very low and are not likely to cause any interference
Résumé du contenu de la page N° 6
Guidance and manufacture’s declaration – electromagnetic immunity The 1528L is intended for use in the electromagnetic environment specified below. The customer or the user of the 1528L should assure that it is used in such an environment. Immunity Test IEC60601 test level Compliance level Electromagnetic environment – guidance Portable and mobile RF communications equipment should be used no closer to any part of the [EQUIPMENT or SYSTEM], including cables, than the recommen
Résumé du contenu de la page N° 7
Recommended separation distances between Portable and mobile RF communications equipment and the 1528L The 1528L is intended for use in which radiated RF disturbances are controlled. The customer or the user of the 1528L can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the 1528L as recommended below, according to the maximum output power of the communications equipment. Separatio
Résumé du contenu de la page N° 8
Classification With respect to electrical shock, fire in accordance with UL60601-1 and CAN/CSA C22.2 No. 60601-1 This monitor is a CLASS 1 (GROUNDED) DEVICE. This monitor is classified NO APPLIED PARTS EQUIPMENT. Protection against harmful ingress of water: INGRESS PROTECTION (IPX1) This monitor shall be classified as ORDINARY EQUIPMENT, not intended or evaluated for use in the presence of flammable anesthetic mixture with air, oxygen, or nitrous oxide. Mode of Operati
Résumé du contenu de la page N° 9
Table of Contents Warnings and Cautions.................................................................................. iv EMC Guidance................................................................................................................ v Classification................................................................................................................viii INTRODUCTION .......................................................................................... 3 Pr
Résumé du contenu de la page N° 10
Type .......................................................................................................................... 22 H. Scan (KHz)........................................................................................................... 22 V. Scan (Hz).............................................................................................................. 22 Polarity............................................................................................................
Résumé du contenu de la page N° 11
CHAPTER INTRODUCTION Product Description The 1528L is a medical 15-inch touchmonitor which uses liquid crystal monitor (LCD) technology, designed to present information to the operator, care-giver and the patient. The 1528L features both serial and USB touch interfaces as standard configuration. The 1528L functionally consists of a 15-inch LCD main monitor with a touchscreen. The monitor element is a 15.0 inch diagonal XGA resolution (1024x768) LCD monitor. Three types of touchscree
Résumé du contenu de la page N° 12
External Medical Grade Power Adapter The 1528L is powered by an external medical grade universal input power adapter. Power adapter: AC power: Input voltage 100 - 240 Vac Input frequency 50 / 60 Hz DC output: 12 Vdc Line and load regulation: ± 3 % 4
Résumé du contenu de la page N° 13
CHAPTER INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following items are present and in good condition: 5
Résumé du contenu de la page N° 14
Product Overview Front View Rear View 6
Résumé du contenu de la page N° 15
Side View Kensington™ Lock The Kensington™ lock is a security device that prevents theft. To find out more about this security device, go to http://www.kensington.com. USB Interface Connection Your touchmonitor comes with one USB cable. (For use with Windows 2000, ME, and XP systems only.) To set up the monitor, please refer to the following figures and procedures: 7
Résumé du contenu de la page N° 16
Remove the Cable Cover The cables are connected at the back of the monitor. CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. To remove the cable cover, place your thumbs at the top corners of the cable cover where the indents are (above the arrows). Gently press and pull the cover toward yourself. NOTE Before connecting the cables to the touchmonitor, route all the cables that you will be using through
Résumé du contenu de la page N° 17
Connect one end of the video cable to the rear side of computer and the other to the LCD. Tighten by turning the two thumb screws clockwise to ensure proper grounding. You can select D-SUB15 video cable or DVI video cable, shown respectively. Connect one end of the speaker cable to the speaker port in the computer and the other end to the port in the monitor. or Connect one end of the Serial or USB cable to the rear side of the computer and the other to the LCD monitor, show
Résumé du contenu de la page N° 18
Replace the Cable Cover After you have attached all the cables to the monitor; gently bring all the cables toward the center so they fit under the cable cover lip. Snap the cable cover in place over the connections. Optimizing the LCD Monitor To ensure the LCD monitor works well with your computer, configure the monitor mode of your graphic card to make it less than or equal to 1024 x 768 resolution, and make sure the timing of the monitor mode is compatible with the LCD monitor. Refer
Résumé du contenu de la page N° 19
Additional drivers and driver information for other operating systems (including Macintosh and Linux) are available on the Elo TouchSystems web site at www.elotouch.com. Your Elo USB touchmonitor is “plug-and-play” compliant. Information on the video capabilities of your touchmonitor is sent to your video monitor adapter when Windows starts. If Windows detects your touchmonitor, follow the instructions on the screen to install a generic plug-and-play monitor. Refer to the appropriate sec
Résumé du contenu de la page N° 20
4. Follow the directions on the screen to complete the driver setup for your version of Windows. 12
