Résumé du contenu de la page N° 1
SyncMaster 510MP / 710MP
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Résumé du contenu de la page N° 4
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heav
Résumé du contenu de la page N° 5
Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be do
Résumé du contenu de la page N° 6
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or a fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Résumé du contenu de la page N° 7
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire. Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause
Résumé du contenu de la page N° 8
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. This may cause malfunction, an electric shock or a fire. Always contact the Servic
Résumé du contenu de la page N° 9
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide and Natural Power Cord Signal Cable(15 pin D-Sub) Color/Driver Installation CD Remote Control / Batteries (CR2025) Monitor Audio Cable Warranty Card Quick Setup Guide (Not available in all locations)
Résumé du contenu de la page N° 10
For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model. 1. SOURCE button 5. Left-Right / Volume button 2. MagicBright™ button 6. MENU button 3. AUTO / EXIT button 7. Power button 4. Up-Down / Channel button 8. Power indicator
Résumé du contenu de la page N° 11
For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model. Remove the cover to connect the cables. (Pull the joining part to remove the cover.) A. Power port Connect the power cord for your monitor to the power port on the back of the monitor. B. Signal port Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. C. Antenna Connection
Résumé du contenu de la page N° 12
For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model. The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor. 1. Button Names 1. POWER button 2. MagicBright™ button 3. MUTE button 4. AUTO / P
Résumé du contenu de la page N° 13
Turn on your computer and monitor. If your monitor displays an image, installation is complete. 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. 2. Connect the signal cable to the video port on your computer. 3. Connect the audio cable for your monitor to the audio port on the back of your computer. 4. Turn on both your computer and the monitor. 5. You may enjoy clear and quality sound from the computer sound card
Résumé du contenu de la page N° 14
AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor. 1. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on. 1. AV input devices like DVDs, VCRs or Camcorders are connected to the S-Video (V1) or Vid
Résumé du contenu de la page N° 15
2. Connecting TV You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer. 1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable. 2. Turn on the monitor. 3. Select TV using Source button among the external signal adjustment buttons. 4. Select a desired TV channel. As this product
Résumé du contenu de la page N° 16
4. Connecting Headphones You may connect your headphones to the monitor. 1. Connect your headphones to the Headphone-out port.
Résumé du contenu de la page N° 17
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monit
Résumé du contenu de la page N° 18
2. Windows XP/2000 Refer to "Installing the Monitor Driver and User Manual" CD-ROM supplied with the monitor. When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer. 1. Insert CD into the CD-ROM driver. 2. Click " Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the " OK" button. 4. Click the " Install" button in th
Résumé du contenu de la page N° 19
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monito
Résumé du contenu de la page N° 20
4. Click the Properties" button on the " Monitor" tab and select " Driver" tab. 5. Click " Update Driver.." and select " Install from a list or.. " then click " Next" button. 6. Select " Don't search ,I will.. " then click " Next" and then click " Have disk". 7. Click the " " button then choose A:(D:\Driver) and choose your monitor model in the model list Browse and click the " " button. Next
