Résumé du contenu de la page N° 1
SyncMaster 2693HM/2493HM
LCD Monitor
User Manual
imagine the possibilities
Résumé du contenu de la page N° 2
Safety Instructions Notational Note Please read the following safety instructions as they are designed to prevent damage to property and harm to the user. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Notational Conventions Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground to prevent an electric Do not touch shock Power When not used for extended
Résumé du contenu de la page N° 3
Safety Instructions Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. • This may cause electric shock or fire. Do not connect too many extension cords or plugs to one outlet. • This may cause fire. Do not disconnect the power cord while using the monitor. • A surge may be caused by the separation and may damage the mon- itor. Do not use the power cord when the connector or plug is dusty. • If the connector or plug of the power cord is dust
Résumé du contenu de la page N° 4
Safety Instructions Do not place the product on the floor. • Take care, as someone, specifically children may trip over it. TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. • Otherwise, this may cause fire. Keep any heating devices away from the power cable. • A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. • Any increase in the internal
Résumé du contenu de la page N° 5
Safety Instructions Do not spray water or detergent directly onto the monitor. • This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. • A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. • Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet
Résumé du contenu de la page N° 6
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. • This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. • Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small
Résumé du contenu de la page N° 7
Safety Instructions Viewing the monitor continuously at a too close angle may result in damage to your eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. • Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product
Résumé du contenu de la page N° 8
Safety Instructions • Adjust the monitor angle so that there is no reflected light on the screen. Try to maintain your arms perpen- dicular to your armpits. • Keep your arms level with the back of your hands. • Keep the angle of the elbow perpendicular. • Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart. 7
Résumé du contenu de la page N° 9
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Without stand With stand Monitor Monitor & Sliding stand Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables D-Sub Cable Power Cord Sold separately DVI Cable HDMI Cable Headphones 8
Résumé du contenu de la page N° 10
Introduction Sold separately Stereo Cable USB Cable Others Cleaning Cloth Note This is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count. Note The resolu
Résumé du contenu de la page N° 11
Introduction Front Note Touch them lightly with your fingers to use them. MENU button [MENU/ ] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Customized Key You can customize key assignment for the Custom button according to your pref- erences. Note You can configure the Customized key for a required function via Setup > Cus- tomized Key. Volume button When OSD is not on the screen, push the button to adjust volume. >> Click here
Résumé du contenu de la page N° 12
Introduction Note If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. >> Click here to see an animation clip AUTO button Use this button for auto adjustment. >> Click here to see an animation clip Power button [ ] Use this button for turning the monitor on and off. Power Indicator This light glows blue during normal operation, and blinking blue once as the mon- itor saves your adjustments. Note See PowerSaver described in the manual
Résumé du contenu de la page N° 13
Introduction POWER S/W Switch the monitor on and off. POWER IN Connect the power cord for your monitor to the POWER IN port on the back of the monitor. HDMI IN / DVI IN(HDCP) / RGB IN HDMI IN Connect the HDMI IN terminal at the back of your monitor to the HDMI terminal of your digital out- put device using a HDMI cable. DVI IN(HDCP) Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor. RGB IN Connect the RGB IN terminal at the back of your monitor to your computer. AUDIO IN
Résumé du contenu de la page N° 14
Introduction Note To use DOWN (Downstream Port), you have to connect the UP (Upstream Cable ) to the PC. Make sure to use the USB cable supplied with this monitor to connect the monitor's UP port and your computer's USB port. Kensington Lock The Kensington lock is a device used to physi- cally fix the system when using it in a public place. (The locking device has to be purchased sepa- rately.) Note For using a locking device, contact where you purchase it. Stand Stopper Remove the fixing
Résumé du contenu de la page N° 15
Connections Connecting Cables Connect the power cord for your monitor to the POWER IN port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI IN(HDCP) Port on the back of your Mo
Résumé du contenu de la page N° 16
Connections Connecting Using a HDMI Cable 1. Input devices such as digital DVD are connected to the HDMI IN terminal of the monitor using the HDMI cable. When all the connections are completed, connect the power cords for the monitor and DVD (or the device connected to the digital output terminal). Select HDMI using the SOURCE button. Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the monitor using a DVI to HDMI cable
Résumé du contenu de la page N° 17
Connections The USB port of the monitor supports High-Speed Certified USB 2.0. High speed Full speed Low speed Data Rate 480 Mbps 12 Mbps 1.5 Mbps Power Consumption 2.5 W 2.5 W 2.5 W (Max., each port) (Max., each port) (Max., each port) 1. Connect the UP port of the monitor and the USB port of the computer with the USB cable. Note To use DOWN port, you have to connect the UP (Upstream Cable) to the PC. Make sure to use the USB cable supplied with this monitor to connect the monitor's UP por
Résumé du contenu de la page N° 18
Connections Note When connecting a device to the DOWN port of the monitor, connect the device using a cable appropriate to the device. (For the purchase of the cable and external devices, ask the service center of the corresponding product.) The company is not liable for problems or damages to an external device caused by using an unauthorized cable for the connection. Some products do not follow the USB standard, and it may cause a malfunction of the device. If the device malfunctions even if
Résumé du contenu de la page N° 19
Connections Tilt angle Using ( ), You can adjust the tilt angle within a range of 5° forward to 25° backward for the most comfortable viewing angle. Sliding stand / Pivot stand Stand Stopper Note When rotating the monitor screen, you should lift it to the maximum height of the stand and then lean the top backwards. Otherwise, the corners of the monitor screen may come into contact with the floor and become damaged. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant mounti
Résumé du contenu de la page N° 20
Connections Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. • Do not use screws longer than the
