Résumé du contenu de la page N° 1
A-20
Owners Manual
A-20 Left Monitor Serial Number:
A-20 Right Monitor Serial Number:
A-20 Control Amplifier Serial Number:
Copyright 2001 NHTPro, a Recoton Corporation Brand
Résumé du contenu de la page N° 2
Safety Instructions -- Please Read First CAUTION: To reduce the risk of electric shock, do not remove CAUTION the cover (or back). No user serviceable parts are inside; refer RISK OF ELECTRIC SHOCK DO NOT OPEN servicing to qualified personnel. WARNING: SHOCK HAZARD-DO NOT OPEN. AVIS: RISQUE DU CHOC ELECTRONIQUE- WARNING: To reduce the risk of fire or electric shock, do NE PAS OUVRIR. not expose this appliance to rain or moisture. This symbol wherever it appears, alerts you to the presence This s
Résumé du contenu de la page N° 3
INTRODUCTION: Thank you for your selection of the A-20. Your studio monitors are a critical element in the countless decisions made during recording, mixing, mastering and other key aspects of audio production. They must deliver a transparent, neutral and revealing assessment of sound, so that you have the information you need to choose and place microphones, set Eq’s, balance mixes... In other words, deliver exceptional product. The A-20 is capable of state of the art sonic resolution and flexi
Résumé du contenu de la page N° 4
SYSTEM CONNECTIONS: CAUTION: MAKE ALL CONNECTIONS WITH THE AC POWER OFF! CAUTION: CONNECTING THE OUTPUT OF THE A-20 CONTROL AMPLIFIER TO ANY EQUIPMENT OTHER THAN THE A-20 OR C-20 MONITOR MAY CAUSE EQUIPMENT DAMAGE. CONTROL AMPLIFIER INPUT SECTION: The A-20 Control Amplifier accepts both balanced and unbalanced inputs on either XLR or 1/4” TRS connectors. These connectors are hardwired in parallel within the A-20 to allow for convenient equipment chaining, but only one signal source should be phy
Résumé du contenu de la page N° 5
USING THE A-20 CONTROL FUNCTIONS: The A-20 controls are designed for utility and repeatability under varying conditions. You should find the effects of the controls sonically subtle, with little impact on the basic character and accuracy of the speaker. We encourage experimentation to fine tune the system to the requirements of your particular installation. 1 +4 MF +11 -3 POWER 2 0 M -10 NF FF 100 MODE PHONES SPL VAC TMP SENSITIVITY BOUNDARY POSITION Control A-20 Amplifier Fig. 5 A-20 Control Am
Résumé du contenu de la page N° 6
BOUNDARY CONTROL: Reflective boundaries, such as floors, walls, even table tops, reinforce a speaker’s low frequency output. Conversely, placing speakers out into a room decreases bass response. The highest low frequency output is with the BOUNDARY control in the “0” position, which assumes no significant boundary reinforcement is present. Each control step attenuates low frequencies by 1.5 dB (at 50 Hz), with rapidly decreasing effect above 300 Hz. Refer to the diagram in Fig. 6 for information
Résumé du contenu de la page N° 7
SPEAKER PLACEMENT: The A-20 Monitor System is intended to provide consistent performance over a wide range of placement situations. This is accomplished through the use of electrical controls, wide dispersion drivers, advanced enclosure design and carefully chosen crossover characteristics. Nevertheless, it is always worth investing time and effort experimenting with optimum loudspeaker placement. In all cases, A-20 Monitors should be set up symmetrically equidistant from the listening position;
Résumé du contenu de la page N° 8
SYSTEM SPECIFICATIONS: Type: Modular, two- piece powered near/mid/far field monitor. Configuration: 2-way acoustic suspension. Woofer: 6.5" curvilinear treated paper. Butyl surround. Tweeter: 1" metal dome, textile surround, ferrofluid cooled and damped. Magnetic Shielding: Partial, 12-18” working distance from PC monitor recommended. PERFORMANCE SPECIFICATIONS: Amplifier Power: 250W (continuous RMS/ch), 400W (100ms peak). Peak Acoustic Output: 117 dB SPL (100ms pink noise @ 1M). Residual hum/no
