Résumé du contenu de la page N° 1
DIAMOND VIEW MONITORS DIAMOND VIEW MONITORS DIAMOND VIEW MONITORS DIAMOND VIEW MONITORS
A REGISTERED TRADE MARK OF MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD.
1770G
Colour Monitor
17” (43cm) CRT Size,
16” (40.6cm) Max. Viewable Area
User’s Manual
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
Table of Contents Safety Instructions for Display Monitors........................................................................................ii Maintenance................................................................................................................................................iii Chapter 1 Introduction ......................................................................................................................................1 Unpacking the Package........
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
Copyright Copyright © 2000 Mitsubish Electric Australia Pty. Ltd All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer Mitsubish Electric Australia Pty. Ltd makes no representations or warranties, e
Résumé du contenu de la page N° 6
Safety Instructions for Display Monitors 1. The AC plug isolates this equipment from the AC Power supply. 2. Unplug the monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Slots and openings in the cabinet and the back or bottom are provided for ventilation. They must not be blocked or covered. This computer monitor should never be placed near or over a radiator or heat register, or in a built-in installation
Résumé du contenu de la page N° 7
Maintenance ✘ Do not expose the monitor to direct sunlight or heat. ✘ Do not spill liquid onto the monitor. ✘ Do not attempt to open the monitor. You may be hurt by electric shock. For service, call your place of purchase. Opening your monitor may also void warranty. ✘ Do not use your monitor when magnets or electronic products are operating nearby. ✘ Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen. Wipe it with clean, soft clothes applied with m
Résumé du contenu de la page N° 8
Résumé du contenu de la page N° 9
Introduction 1 Unpacking the Package Check following items. If they are missing or damaged, consult your place of purchase immediately. Colour monitor Swivel base User’s manual Power cord Locate the model name and the serial number labeled on the back of your monitor. Write down the related information of your monitor and dealer in the space on page ii for future reference. Features Your 1770G has the following features: Plug’n Play Compatibility With its DDC1
Résumé du contenu de la page N° 10
Easy to Use On Screen Display The On-Screen Display (OSD) allows you to adjust all settings simply with on-screen menus. Power Saving Function The power management complies with VESA DPMS standard. When the system is idle (off mode), the monitor automatically cuts its power consumption up to 95%. Green Commitment No CFCs are used in the manufacturing process of your monitor. It complies with the US government’s Energy Star standards and the rigorous standards of the Scandinavian c
Résumé du contenu de la page N° 11
Getting Started 2 Installing the Monitor This monitor is equipped with an autosensing power supply for voltage ranges 100~240V AC, 50~60Hz. To install the monitor : 1. Make sure that the system power is turned off. 2. Please refer to the instructions below to connect the signal cable through D-SUB . 3. Connect the power cord to the monitor and attach it to power source. 4. Turn on the computer and the monitor. 3
Résumé du contenu de la page N° 12
Connecting through D-SUB signal connector 1. Make sure that the system power is turned off. 2. Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer. To connect the monitor to an older type Apple Macintosh through a D-Sub cable, you need to use an Apple Macintosh signal adaptor to connect the video signal port of your computer to the monitor signal cable. Adaptors are available from Mitsubishi Electric Australia. Pleas
Résumé du contenu de la page N° 13
Adjusting the Monitor 3 A Look at the Control Panel 1 2 3 4 5 Exit Enter Adjusting the Monitor You can adjust the monitor with the On-Screen Display (OSD) menus. There are 5 keys for user’s control. They include Exit, , , Enter and Power Switch. The following is the introduction: Panel key introduction 1. Exit key : returns to last page, saves or quits the menu system. 2. / key : adjusts the parameter setting to a lower v
Résumé du contenu de la page N° 14
Selecting function and making adjustments 1) Contrast hot-key mode 1. Press to enter contrast hot-key mode 2. Press or to adjust the setting. 2) Brightness hot-key mode 1. Press to enter brightness hot-key mode. 2. Press or to adjust the setting. 3) Main menu mode Grouped by functions, the OSD offers 6 major functions in Main Menu for making adjustments: Contrast, Geometry, Colour adjustment, Recall, Degaussing and Miscellaneous. The following describes the contents of
Résumé du contenu de la page N° 15
Make adjustments 1. In Main Menu: Press or to locate the item you desire to change. 2. Press Enter to go into the Sub Menu. 7
Résumé du contenu de la page N° 16
3. Press or to locate the function item. Then press Enter and or to make the adjustment. etc Sub menu Function name Hor. Position Scale 75 Enter:Save Enter:Save Exit : Exit Exit : Exit 4. Press Exit to save the setting. 5. Press Exit to return to main menu. Control functions available in main menu 1. Luminance Contrast: adjusts the difference between the light and dark areas. Brightness: adjusts the brightness of the display. 2. Geom
Résumé du contenu de la page N° 17
Unbalance: adjusts the pincushion balance if both sides of the display are bowed toward the left or right. Trapezoid: makes the vertical edges of the display parallel. Parallelogram: aligns the top and bottom edges of the image. Top corner: adjusts the edge curvature at the top corners of the image. Bottom corner: adjusts the edge curvature at the bottom corners of the image. 3. Colour Adjustment Colour
Résumé du contenu de la page N° 18
4. Recall geometry preset setting Locate and press Enter to recall the preset settings. The word “Recall” will keep blinking on the screen in the process of recall. This page is also a “status display” that shows current horizontal and vertical frequencies. Please note that the resolution data. Is only displayed if you are using a graphics signal that corresponds with one of the monitor’s presets. 5. Manual degaussing function To eliminate colour shading or impurity induced by
Résumé du contenu de la page N° 19
The on-screen menu will automatically disappear after 20-second’s of inactivity. If changes have been made, the monitor will automatically save them. Timing Setting By making adjustments of your video card settings, you can set the timing and the refresh rate to your preferences. The monitor will automatically save the settings. Your monitor can accept horizontal frequencies ranging from 30 KHz to 72 KHz and vertical frequencies from 50 Hz to 120 Hz. However, due to different res
Résumé du contenu de la page N° 20
Troubleshooting and Useful Hints 4 Troubleshooting Make sure that your monitor is properly installed if you encounter any trouble using this product (For hardware installation, see Chapter 2, Getting Started). If the problems persist, check this chapter for possible solutions. There is no picture on the screen. Check: Video sync signal. The video sync signal from the graphics card must be as specified for the monitor. Power saving mode. Press any key and move the mouse
