Résumé du contenu de la page N° 1
XT4862
14 INCH
COLOR MONITOR
USER'S
MANUAL
Features:
• 1024 x 768, Non-Interlaced
• .28 mm Dot Pitch
• 72 Hz Refresh Rate (VGA/SVGA)
• Power Saving Operation (VESA DPMS)
• Non-Glare Screen
• Full Screen Display
• Easy Access Front Controls
• Unlimited Palette of Colors
• Plug and Play
Part #MAN094 Rev 1.0 M1450
Résumé du contenu de la page N° 2
Table of Contents Section 1 - General Information .........................................2 Section 2 - Installation ........................................................3 Section 3 - Monitor Controls and LEDs..............................4 Section 4 - Troubleshooting ...............................................5 Appendix A - Specifications ...............................................5 Appendix B - Video Cable Pinout .......................................6 Appendix C - Three Year Warr
Résumé du contenu de la page N° 3
Section 1 - General Information Congratulations on purchasing a MaxTech 14-inch Color Monitor. The monitor has one of the finest CRTs available in the industry, providing a full range of video display resolutions and complies with the MPR-I standard to reduce electromagnetic emissions. The monitor is PnP (Plug and Play) compliant to simplify setup and configuration in Windows 95 or other PNP operating systems. The monitor has a 0.28 mm dot pitch display with a 65 MHz video bandwidth. It supports
Résumé du contenu de la page N° 4
The monitor enters DPMS OFF mode when the computer turns off both the Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 5W. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top. • Insert the hooks on the swivel base into the slots in the bottom of the monitor. Push down and forward o
Résumé du contenu de la page N° 5
• Make sure that power to the monitor and the computer is off. • Connect the cable from the back of the monitor to the video connector on the computer. • Attach the power cord to the monitor and plug it into an AC outlet. • The monitor is now ready for use. Section 3 - Monitor Controls and LEDs Figure 3-1 Controls and LEDs 1 2 34 5 6 7 8 9 1.Power Switch: Press to turn the monitor on, press again to turn the monitor off. 2. Power Indicator: A green LED indicates the monitor is fully powered on.
Résumé du contenu de la page N° 6
8. Contrast Control: Adjusts the contrast. Turn clockwise to increase the contrast. 9. Brightness Control: Adjusts the display brightness. Turn clockwise to increase the brightness. Section 4 - Troubleshooting No picture, power indicator off • Check AC cord is plugged into outlet and monitor. • Turn on the power switch. No picture, power indicator green. • Check that video cable is connected completely. • Adjust brightness and contrast controls. • Turn the computer on. No picture, power indicato
Résumé du contenu de la page N° 7
Deflection Geometric distortion H.<=2.5mm, V.<=2.5mm Linearity distortion H<=10%, V<=8% Pincushion distortion <=2mm High voltage regulation H<=4mm, V<=4mm(0-25FL) Low radiation* MPR-I specification Front controls Power, Brightness, Contrast, Horizontal-Size, Hori- zontal-Position, Vertical-Size, Vertical-Position, Pin- cushion Power saving Display Power Management Signaling (DPMS) SUSPEND mode 25W (Max.) OFF mode 5W (Max.) Plug and Play DDC1 Input voltage 100~240VAC, 50/60 Hz Power consumption 8
Résumé du contenu de la page N° 8
Appendix C - Three Year Warranty MaxTech warrants to the original buyer of this product against defects in material and workmanship for three years from the date of purchase. Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in North America by MaxTech or which is not purchased in North America from an authorized MaxTech Dealer. 2. Any product on which the
Résumé du contenu de la page N° 9
address provided by the technician when you call. We recommend that the unit be insured. This warranty is valid for products sold in North America only. Contact your local authorized distributor or dealer for the warranty offered in other areas. All warranty services must be performed by Authorized Service Centers. There are no user serviceable parts inside the unit. Do not remove any components or attempt to service the unit by any unauthorized service center. This warranty is voided if the pro
Résumé du contenu de la page N° 10
• Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio / TV technician for help Notice: Shielded cables, if any, must be used in order to comply with the emission limits. Notice: Any change or modification not expressly approved by the Grantee of the equipment authorization could void the us
