Résumé du contenu de la page N° 1
XT7800
17 INCH
COLOR MONITOR
USER'S
MANUAL
Features
• 0.28 mm Dot Pitch
• 1280 x 1024, Non-Interlaced
• 90 Hz Refresh Rate (VGA/SVGA)
• Power Saving Operation (VESA DPMS)
• Non-Glare Screen
• Full Screen Display
• Digital Controls
• RGB Color Match Controls
• Low Radiation
Part #MAN061 Rev. 1.0
Résumé du contenu de la page N° 2
Table of Contents Section 1 General Information ......................................................... 2 Section 2 Installation........................................................................ 3 Section 3 Monitor Controls and LEDs ............................................. 4 Section 4 Troubleshooting ............................................................... 6 Appendix A Specifications ................................................................... 6 Appendix B Two Year War
Résumé du contenu de la page N° 3
Section 1 - General Information Congratulations on purchasing the MaxTech 17-inch Color Monitor. The monitor has one of the finest CRTs available in the industry, providing a full range of video display resolutions and complies with the MPR-II standard to reduce electromagnetic emissions. The monitor has a 0.28 mm dot pitch display with a 75 MHz video bandwidth. It supports video resolutions ranging from 640 x 350 to 1280 x 1024 (non-interlaced). The monitor can be used with video cards supporti
Résumé du contenu de la page N° 4
Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 5W. While in this mode the first and second LEDs in the Power Indicator (LEDs A and B in Figure 3-1) are off. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top. • Insert the hooks on the swivel base into the slots in the bottom of
Résumé du contenu de la page N° 5
on the computer. • Connect the supplied power cord into the AC connector on the back of the monitor and the other end into an AC outlet. • The monitor is now ready for use. Section 3 - Monitor Controls and LEDs Figure 3-1 Controls and LEDs A B 1 C 12 (on back) 11 10 9 8 7 6 5 4 3 2 1. Power Indicator LEDs A, B, and C (See Figure 3-1) indicate the operational state of the monitor. 1.1 LEDs A, B and C are lit: The monitor is in normal operating mode. 1.2 Only LEDs B and C are lit: The monitor is i
Résumé du contenu de la page N° 6
5. Contrast Control Adjusts the display contrast. 6. Memory Recall Push to reset the display to the default parameters. 7-10 On-Screen Display Controls The On-Screen Display (Refer to Section 3.1) is controlled using buttons 7 through 10. The On-Screen Display is enabled by pressing any of these buttons. 7. ADJ+ Pressing this button will increase the value of the highlighted setting. 8. ADJ- Pressing this button will decrease the value of the highlighted setting. 9. Cursor+ Pressing this button
Résumé du contenu de la page N° 7
C. Horizontal-Position Adjusts the horizontal position. The ADJ+ button moves the display to the right. The ADJ- button moves the display to the left. D. Vertical-Position Adjusts the vertical position. The ADJ+ button moves the display up. The ADJ- button moves the display down. E. Pincushion Adjusts the shape of the left and right sides of the display. The ADJ+ button makes the display sides curve out. The ADJ- button makes the display sides curve in. F. Color Adjustment - Red Adjusts the inte
Résumé du contenu de la page N° 8
Data Area 12.75 x 9.625 in. Preset Display Modes Mode Resolution V. Frequency H. Frequency VGA 640 x 350 70 Hz 31.47 KHz VGA 640 x 400 70 Hz 31.47 KHz VGA 640 x 480 60 Hz 31.47 KHz SVGA 800 x 600 56 Hz 35.16 KHz 8514A 1024 x 768 87 Hz 35.52 KHz VGA 640 x 350 84 Hz 37.86 KHz VGA 640 x 400 84 Hz 37.86 KHz VGA 640 x 480 84 Hz 37.86 KHz SVGA 800 x 600 72 Hz 48.09 KHz SVGA 800 x 600 60 Hz 37.88 KHz SVGA 800 x 600 72 Hz 48.08 KHz Ultra VGA 1024 x 768 60 Hz 48.37 KHz Ultra VGA 1024 x 768 70 Hz 56.48 KH
Résumé du contenu de la page N° 9
2. Any product on which the serial number has been defaced, modified or removed. 3. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature, commercial or industrial use, unauthorized product modification, or failure to follow instructions supplied with the product. b. Repair or attempted repair by anyone not authorized by MaxTech. c. Any shipment of the product (claims must be presented to the carrier). d. Removal
Résumé du contenu de la page N° 10
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult th
