Instruction d'utilisation Kenwood DDX7019

Résumé du contenu de la page N° 1

MONITOR WITH DVD RECEIVER
DDX7019
DDX7039
INSTALLATION MANUAL
© B54-4522-00/00 (KV/RV)

Résumé du contenu de la page N° 2

Accessories 1 ..........1 2 ..........1 3 ..........2 4 ..........1 5 ..........1 6 ..........6 7 ..........6 8 ..........1 | 2 DDX7019/DDX7039

Résumé du contenu de la page N° 3

Installation Procedure 1. To prevent a short circuit, remove the key from the € ignition and disconnect the - battery. • If the power is not turned ON (or it is ON, but will be OFF 2. Make the proper input and output wire immediately), the speaker wire may have a short-circuit connections for each unit. or touched the chassis of the vehicle and the protection 3. Connect the speaker wires of the wiring harness. function may have been activated. Therefore, the speaker 4. Connect the wiring h

Résumé du contenu de la page N° 4

Connection If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may Ignition key cause a short circuit, that in turn may start a fire. Always switch connect those wires to the power source running through the fuse box. ACC A Ignition wire (Red) B A Car fuse box Battery wire (Yellow) Car fuse box B (Main fuse) FUSE ( 5A ) Ground wire (Black) - (To car chassis) C C Antenna Cord Battery Connect to the vehicle's parking brake detection switch

Résumé du contenu de la page N° 5

FUSE ( 10A ) Rear view Cooling fan FM/AM antenna input Accessory 1 REVERSE ILLUMI White/Black To front left speaker + REMO.CONT White Gray/Black To front right speaker MUTE + Gray Green/Black To rear left speaker + Green ANT. CONT Purple/Black To rear right speaker + P CONT Purple EXT.CONT | English 5 REAR L FRONT R REAR R FRONT L

Résumé du contenu de la page N° 6

System Connection USB device USB terminal (commercially available) Do not connect. Rear view ■ Audio/Visual Output • Visual output (Yellow) ■ Audio/Visual input • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output

Résumé du contenu de la page N° 7

iPod iPod AUDIO IN VIDEO IN Optional Accessory Connection iPod (commercially available) Navigation System (Optional Accessory) KCA-iP300V (Optional Accessory) Audio Input Connection cable Audio Output (Included in the Navigation System) (Black) Visual Input Visual Output (Yellow) Rear view USB terminal USB terminal Connection cable (Included in the Disc changer) Disc Changer etc. (Optional Accessory) TV Tuner (Optional Accessory) Connection cable (Included in the TV tuner) | English 7

Résumé du contenu de la page N° 8

Installing the Escutcheon For General Motors 1. Refer to the section and then remove the hard rubber frame. the opening in the vehicle. 2. Cut out accessory 4 to meet the shape of the opening of the center console. 3. Attach accessory 4 to the unit. Accessory 4 For Toyota/Scion 1. Refer to the section and then remove the hard rubber frame. 2. Cut out accessory 4 as illustrated. Access

Résumé du contenu de la page N° 9

Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw Metal mounting strap Accessory 2 (commercially available) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation on Toyota, Nissan or Mitsubishi Car using Brackets Acce

Résumé du contenu de la page N° 10

Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Remove the Hex-head screw with integral washer Lower the frame and pull it forward as shown in (M4 × 8) on the back panel. the figure. 3. Insert the two removal tools 3 deeply into the Remo