Résumé du contenu de la page N° 1
COLOR VIDEO MONITOR
INSTRUCTIONS
TM-1011G
LCT1989-001A-H
En_TM-1011_Cover.p65 1 06.2.14, 22:37
Résumé du contenu de la page N° 2
Thank you for purchasing this JVC Color Video Monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling of the monitor, be fully aware of all the following precautions. FCC INFORMATION (U.S.A. only) WARNINGS CAUTION: Changes or modification not approved by JVC To prevent fire or shock hazard, do not expose this could void the user's aut
Résumé du contenu de la page N° 3
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 220-240 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries. Power cord Power supply voltage: AC 120 V AC 220-240 V AC 220-240 V Countries: U.S.A. and Canada European countries United Kingdom Warning: • Do not use the
Résumé du contenu de la page N° 4
Controls and Features 7 Front Panel 1 4 23 56 7 8 9pq 1 Tally lamp 4 MENU/VOLUME control This lamp is controlled by the tally function of the • Adjusts the volume level by MAKE/TRIGGER terminal. moving the control to / . ☞ “How to Use the MAKE/TRIGGER Terminal” on pages • Displays or closes a menu screen 14 and 15 by pushing in the control. •You can set the lamp color to red or green. •Turns off/on the sound each time ☞ “TALLY SELECT” on page 12 moving the control to when no 2 CHROMA ( )/PHASE
Résumé du contenu de la page N° 5
5 UNDER SCAN button 7 About the status display Reduces the screen size so that the whole screen is Displays information of the current input selection displayed. and the monitor settings for about 3 seconds. To show the status display, set “STATUS DISPLAY” 6 BLUE CHECK button to “AUTO” or “MANUAL” beforehand. Displays the blue video signal only. ☞ “STATUS DISPLAY” on page 13 7 COLOR OFF button Pressing the INPUT SELECT button currently Displays the luminance signal only. selected shows the statu
Résumé du contenu de la page N° 6
Controls and Features (cont.) 7 Rear Panel w r e t y u Pin terminals of the DC IN 12 V connector: w Power input connectors You can use either AC or DC power supply to operate the monitor. Pin No. Signal AC IN: Connect to an AC outlet with the 1 GND provided AC power cord. (AC 120 V/ 4 1 3 2 — 2 220-240 V, 50 Hz/60Hz). DC IN 12 V: Connect the power cord from the DC 3 — power supply (12 V). 4 DC 12V NOTES: • Regarding the DC power supply, consult with your dealer. • While connecting both the AC a
Résumé du contenu de la page N° 7
e AC power switch u DC switch Turns the AC power on and off. Turns the DC power on and off. •I : on : off •I : on : off NOTE: NOTES: •You need to turn on the stand-by button on the front •You need to turn on the stand-by button on the front panel to turn on the monitor after turning on the AC panel to turn on the monitor after turning on the DC power switch. switch. • The monitor consumes the battery even while the r Composite signal input/output terminals monitor is on stand-by. To save bat
Résumé du contenu de la page N° 8
Basic Menu Operations 7About the Menu Screens This monitor features MAIN MENU which contains the functions normally used and SET-UP MENU which contains the initial settings of the monitor. MAIN MENU Items Functions APERTURE CONTROL Compensates the frequency characteristics of the luminance signal of a video signal. sub menu SELECT Selects the positions and the contents of the sub-menu display. ASPECT Selects the aspect ratio. SET-UP MENU Items Functions FUNCTION SETTING Sets the control systems
Résumé du contenu de la page N° 9
7Displaying the Menu 7About “ sub menu” When “ sub menu” is displayed in the menu, only Screens selected item in that menu can be displayed and To display MAIN MENU adjusted. This allows you to make adjustments while Push in the MENU/VOLUME control on the front panel. looking at the actual screen. To display SET-UP MENU Push in the CHROMA/PHASE button while moving the MENU/VOLUME control to . NOTES: •To exit the menu, push in the MENU/VOLUME control several times. • The menu automatically exits
Résumé du contenu de la page N° 10
How to Use MAIN MENU 7MAIN MENU Screens MAIN MENU Setting Items Move the MENU/ VOLUME control to . Move the MENU/ ☞ page 9 VOLUME control to / to adjust an item. ☞ see below. About “ sub menu” and “reset,” ☞ page 9 *To go back to the previous menu, press the MENU/VOLUME control. NOTE: • Some items do not appear on the menu depending on the signal currently input or if there is no signal input. Those items are not available to use. 7Functions and Adjustment Range of Items APERTURE CONTROL sub m
Résumé du contenu de la page N° 11
How to Use SET-UP MENU 7SET-UP MENU Screens SET-UP MENU Setting Items Move the MENU/ VOLUME control to . ☞ page 13 Move the MENU/ VOLUME control to / to adjust an item. About “ sub menu” and “reset,” ☞ page 9 *To go back to the previous menu, press the MENU/VOLUME control. NOTE: • Some items do not appear on the menu depending on the signal currently input or if there is no signal input. Those items are not available to use. 11 En_11-20_TM-1011G.p65 11 06.2.14, 22:37
Résumé du contenu de la page N° 12
How to Use SET-UP MENU (cont.) 7Functions and Adjustment Range of Items 7 HOUR METER X100h FUNCTION SETTING Displays the total usage time of the monitor in Sets the control systems for hundred-hour units. the COLOR SYSTEM, • 000 O 655 colors of the tally lamp, and NOTES: MAKE/TRIGGER terminal. • When the timer passes 655, it returns to 000. • Can be also used to check • The timer does not count usage time under one hour. the amount of time that the monitor has been used. PICTURE SUB ADJ. 7 COLOR
Résumé du contenu de la page N° 13
7 BLUE CUTOFF 7 TRAPEZOID Adjusts the blue cut-off point. Compensates the trapezoid picture distortion. • MIN O MAX (in 155 grades) • –20 O 00 O +20 –: Enlarges the upper side of the picture. 7 RED CUTOFF +: Reduces the upper side of the picture. Adjusts the red cut-off point. 7 ROTATION • MIN O MAX (in 155 grades) Compensates a picture tilt. SIZE/POSI. ADJ. • –31 O 00 O +31 –: Turns the picture clockwise. Adjusts the size and +: Turns the picture counterclockwise. position of the picture. STATU
Résumé du contenu de la page N° 14
How to Use the External Control 7About the External Control The Monitor has the MAKE/TRIGGER terminal, which allows you to control the monitor by the MAKE (make contact) or TRIG. (trigger) system selected in the function setting. MAKE (make contact) system: Controls the function by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. TRIG. (trigger) system: Controls the function by inputting the pulse signal instantaneously to the corresponding
Résumé du contenu de la page N° 15
Functions controlled by the MAKE/TRIGGER Terminal Display Functions to be controlled Opening Short-circuiting *1 INP. A Changes the input to INPUT A Invalid Valid INP. B Changes the input to INPUT B Invalid Valid CO. OFF Turns on/off COLOR OFF Off On (Monochrome screen) *2 ASPECT Changes ASPECT 4:3 16:9 TALLY Controls the tally lamp Off On *3 TA. SEL Selects the color of the tally lamp Green Red STATUS Turns on/off the status display Off On *1 The TRIG. (trigger) system switches each function by
Résumé du contenu de la page N° 16
Troubleshooting Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Reference Problems Points to be checked Measures (Remedy) pages No power supply Is the AC or DC power plug loose or Firmly insert the power plug. — disconnected? When using the DC power supply, is Charge the battery or replace it with the one — the battery charge
Résumé du contenu de la page N° 17
Reference Problems Points to be checked Measures (Remedy) pages Wrong picture Has the picture position, size, Adjust the picture size (H. SIZE, V. SIZE) or position, wrong distortion, or tilt been changed? position (H. POSITION, V. POSITION) in “SIZE/ picture size POSI. ADJ.” Adjust the picture distortion (PARALLELOGRAM, TRAPEZOID) or tilt (ROTATION) in 13 “DISTORTION ADJ.” It may not be possible to expand the picture due to the selected input mode. In this case, adjustment is impossible. Has th
Résumé du contenu de la page N° 18
Specifications Model TM-1011G Type Color Video Monitor Picture Tube 10" measured diagonally Effective Screen Size Width: 176.9 mm (6 15/16") Height: 137.6 mm (5 3/8") Diagonal: 224.5 mm (8 13/16") Scanning Frequency H: 15 kHz V: 50 Hz/60 Hz Video Band 6 MHz (–3 dB) Horizontal Resolution 280 TV lines Input/Output Terminals Composite signal input/output terminals VIDEO A/VIDEO B: 2 lines, BNC connector x 4 (1 Vp-p, 75 Ω ) * The input (IN) and output (OUT) terminals are bridge-connected. (Auto term
Résumé du contenu de la page N° 19
7Dimensions Unit : mm (inch) Front View Side View 3 338.3 (13 /8") 3 222 (8 /4") 1.5 1 307.8 (12 /8") 1 ( /16") 1 * 183 (7 /4") 1 164 (6 /2") 7 63.5 222 7 3 1 3 3 ( /8") (2 /2") (8 /4") ( /8") Asterisks (*) are used to indicate front panel dimensions. 19 En_11-20_TM-1011G.p65 19 06.2.14, 22:37 3 220 (8 /4") 1 229 (9 /8") * 5 140 (5 /8")
Résumé du contenu de la page N° 20
TM-1011G COLOR VIDEO MONITOR 2006 Victor Company of Japan, Limited 0306STH-MW-MT © En_11-20_TM-1011G.p65 20 06.2.14, 22:37
