Résumé du contenu de la page N° 1
MULTI-FORMAT MONITOR
INSTRUCTIONS
DT-V100CG
The supplied wide mask is attached to the monitor in the
illustration on the right.
LCT1811-001A
LCT1811-001A_Cover.p65 1 05.3.9, 8:08 PM
Résumé du contenu de la page N° 2
Thank you for purchasing this JVC Multi-Format Monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling the monitor, be fully aware of all the following precautions. WARNINGS FCC NOTICE (U.S.A. only) To prevent fire or shock hazard, do not expose this CAUTION: Changes or modifications not approved by monitor to rain or moisture. Dange
Résumé du contenu de la page N° 3
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 220-240 V (For European countries, United Kingdom, or China), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries. Power cord Power supply voltage : AC 120 V AC 220-240 V AC 220-240 V AC 220-240 V Countries : U.S.A. and Canada European countries United Kingdom Ch
Résumé du contenu de la page N° 4
Controls and Features Front Panel 1 23 4 567 8 9 p 1 Tally lamp 4 MENU control This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. “How to Use the MAKE/TRIGGER Terminal” on page 19 Displays or closes a menu screen. • You can set the lamp color to red or green in “TALLY SELECT.” “TALLY SELECT” on page 15 • When you set “FORMAT IND.” to “ON,” this lamp works as the format indicator showing the format of the signal While a menu screen is displayed, currently input. “FO
Résumé du contenu de la page N° 5
5 SCAN SIZE button About the status display Reduces the screen size (under-scan) so that Displays information of the current input selection and the the whole screen is displayed. monitor settings for about 3 seconds. To show the status display, set “STATUS DISPLAY” to 6 SCREENS CHECK button “AUTO” or “MANUAL” beforehand. “STATUS DISPLAY” on page 18 Each time you press this button, the screen Pressing the INPUT SELECT button currently selected changes in the following order: shows the status
Résumé du contenu de la page N° 6
Controls and Features (cont.) Rear Panel q w r e t y q AC inlet t External synchronized signal input/output terminals (for both VIDEO A and VIDEO B) Power input connector. Connect the provided AC Input (IN) and output (OUT) terminals for the complex power cord to an AC outlet (120 V/220-240 V AC, synchronized signals. 50 Hz/60 Hz). • To use these terminals, set “SYNC SELECT” to “EXT.” * Attach the provided Power Cord Holder to prevent “SYNC SELECT” on page 15 accidental disconnection of the AC
Résumé du contenu de la page N° 7
Preparation Attaching the Wide Mask A wide mask is provided with the monitor. This changes the viewable screen area to the 16:9 aspect ratio. Caution: • The wide mask cannot be attached to the monitor after the monitor is mounted in a rack. Mount the wide mask before installing the monitor in a rack. • If you attach and remove the wide mask many times, the screws may not be fixed securely. • Use only the provided screws. 1. Prepare the provided wide mask and 4 screws (for attaching). 2. Attach
Résumé du contenu de la page N° 8
Preparation (cont.) Attaching the Power Cord Holder • The provided Power Cord Holder prevents accidental disconnection of the AC power cord from the AC inlet. • The Power Cord Holder consists of two parts; a case and a cover. 1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws (provided). Caution: Use only the provided screws. 2. Attach the Power Cord Holder cover to the AC power cord. Close the cover until it clicks. 3. Connect the AC power cord to th
Résumé du contenu de la page N° 9
Basic Menu Operations (MAIN MENU, SET-UP MENU) About the Menu Screens This monitor features MAIN MENU which contains the functions normally used and SET-UP MENU which contains the initial settings of the monitor. MAIN MENU Items Functions APERTURE CONTROL Compensates the frequency characteristics of the input video signal. sub menu SELECT Selects the positions and the contents of the sub-menu display. MARKER Controls ON/OFF and other settings of the MARKER SELECT, ZOOM, ASPECT SELECT, and SAFE
Résumé du contenu de la page N° 10
Basic Menu Operations (MAIN MENU, SET-UP MENU) (cont.) Displaying the Menu About “ sub menu” Only displays selected items. (sub-menu display) Allows you Screens to adjust and set items while looking at the actual screen. To display MAIN MENU Press the MENU control on the front panel. To display SET-UP MENU Press the CHROMA/PHASE button while keeping to move the MENU control to . NOTES: • To exit the menu, press the MENU control several times. • The menu automatically exits about 30 seconds a
Résumé du contenu de la page N° 11
How to Use MAIN MENU MAIN MENU Screens MAIN MENU Setting Items Move the MENU control to . page 12 page 13 page 13 Move the MENU control to / to adjust an item. About “ sub menu” and “reset,” page 10 * To go back to the previous menu, press the MENU control. NOTE: Some items may not appear on the menu depending on the input (or the input unit if it is attached) or the input signal. Those items are not available to use. 11 EN07-13_LCT1811-001A-H.p65 11 05.3.9, 8:23 PM
Résumé du contenu de la page N° 12
How to Use MAIN MENU (cont.) Functions, Contents, and Adjustment Range of items APERTURE CONTROL MARKER Compensates the frequency Controls ON/OFF and other characteristics of the input settings of the MARKER video signal. SELECT, ZOOM, ASPECT SELECT, and SAFETY MARKER functions included in the MARKER function. NOTES: LEVEL • For the 4:3 screen ratio, only SAFETY MARKER and R-SAFETY MARKER are displayed. Adjusts the compensate value. The higher the • To set up non-“R-” items, press the MARKER
Résumé du contenu de la page N° 13
R-Y PHASE ASPECT SELECT/R-ASPECT SELECT Sets the R-Y phase. Selects the aspect ratio. • 90/92/94/112 • 4:3/13:9/14:9 R/B GAIN Sets the R/B gain. • 0.56/0.68/0.79/0.86 G-Y PHASE 4:3 13:9 14:9 Sets the G-Y phase. SAFETY MARKER/R-SAFETY MARKER • 236/240/244/253 Displays dotted lines to indicate the areas corresponding to 80%, 88%, or 90% of the screen G/B GAIN size (the aspect ratio setting in “ASPECT SELECT/ Sets the G/B gain. R-ASPECT SELECT”). • 0.30/0.34/0.40/0.45 OFF: SAFETY MARKER
Résumé du contenu de la page N° 14
How to Use SET-UP MENU SET-UP MENU Screens SET-UP MENU Setting Items Move the MENU control to . page 18 Move the MENU control to / to adjust an item. About “ sub menu” and “reset,” page 10 * To go back to the previous menu, press the MENU control. NOTE: Some items may not appear on the menu depending on the input (or the input unit if it is attached) or the input signal. Those items are not available to use. 14 EN14-24_LCT1811-001A-H.p65 14 05.5.13, 2:24 PM
Résumé du contenu de la page N° 15
Functions, Contents, and Adjustment Range of items FUNCTION SETTING FORMAT IND. Sets the tally lamp as the format indicator to show Sets the control systems for the format of the signal currently input. the COLOR SYSTEM, NOTE: synchronized signal, RUSH When setting FORMAT IND. to ON, you cannot use the tally lamp DELAY TIME, colors and function of the MAKE/TRIGGER terminals. functions of the tally lamp, page 19 groups of the audio output ON: Uses the lamp as the format indicator. modes, an
Résumé du contenu de la page N° 16
How to Use SET-UP MENU (cont.) COLOR TEMP./BAL. HOUR METER X100h Displays the total usage time of the monitor in Sets or adjusts the color hundred-hour units. temperature or white • 000 O 655 balance. NOTES: NOTE: • When the timer passes 655, it returns to 000. Use the five items indicated with • The timer does not count the usage time under one hour. mark to make fine adjustments between the monitors. PICTURE SUB ADJ. COLOR TEMP. Selects the color temperature. The standard value (“00”) of
Résumé du contenu de la page N° 17
SIZE/POSI. ADJ. DISTORTION ADJ. Adjusts the size or position Compensates the picture of the picture. distortion, tilt, and the color • Can also be used to adjust heterogeneity caused by the the zoomed picture size. geomagnetic influence. PARALLELOGRAM H. SIZE Compensates the parallelogram picture distortion. Adjusts the horizontal screen size. •–20 O 00 O +20 •–20 O 00 O +20 (*) –: Reduces the screen size horizontally. –: Moves the upper side of the picture to the right, and the lower side t
Résumé du contenu de la page N° 18
How to Use SET-UP MENU (cont.) • When “1-8” is selected, the channel input level for 1, 2, 3 and 4 is STATUS DISPLAY displayed on the left side of the screen, and the channel input level for 5, 6, 7 and 8 is displayed on the right side of the screen. Sets the items related to the • The AUDIO LEVEL METER display moves to inside of the display screens, such as the screen when the ZOOM function is operated. status display or the AUDIO BAR TYPE LEVEL METER display. • Can also be used to set the Se
Résumé du contenu de la page N° 19
How to Use the External Control About the External Control The Multi-Format Monitor has two external control terminals. One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE (make contact) or TRIG. (trigger) method selected in the function setting. MAKE (make contact system): Controls the function by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. TRIG. (trigger system): Controls the function by inputting
Résumé du contenu de la page N° 20
How to Use the External Control (cont.) How to Use the RS-485 Terminal You can control the monitor from your PC via the RS-485 terminal. For details on operating the monitor from the PC, consult the service center. 123 4 5 678 1. Cable Prepare a straight cable with a RJ-45 connector. 2. Communications Specifications Baud Rate: 4800/9600/19200 (factory pre-set; 4800) Data Bits: 8 bits Parity: No parity Stop Bits: 1 bit IN terminal OUT terminal Pin No. Communication Cord: ASCII Cord signal signa
