Résumé du contenu de la page N° 1
Flat Panel Monitor
15.0 inch(381mm) TFT LCD
1024x 768 Addressability
16.7 Million Colors
TCO 95
User Guide
Guide de l’utiliseur
T55A
Benutzerhandbuch
Manual del usuario
Type 9513
Manuale per l’utente
Résumé du contenu de la page N° 2
T55A.book Page 1 Saturday, August 29, 1998 10:37 AM These user’s setup instructions cover typical user environments. The on-screen messages may differ depending on the level of your hardware and software. In some cases you may need to vary the setup procedures. For more information, refer to your computer or operating system manuals or consult your system administrator or dealer. Ces instructions de configuration d’exploitation s’appliquent aux environnements d’utilisation types. Les mess
Résumé du contenu de la page N° 3
T55A.book Page c Saturday, August 29, 1998 10:37 AM DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet. • Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets. • To isolate the monitor from the electric
Résumé du contenu de la page N° 4
T55A.book Page d Saturday, August 29, 1998 10:37 AM GEVAAR Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen: • Verwijder in geen enkel geval de kap. • Stel dit produkt alleen in werking als de voet is bevestigd. • Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens onweer. • Het netsnoer moet worden aangesloten op een geaarde contactdoos met correcte bedrading. • Ook alle apparatuur waarop dit produkt wordt aa
Résumé du contenu de la page N° 5
T55A.book Page e Saturday, August 29, 1998 10:37 AM PERIGO Para evitar o perigo de choques eléctricos: • Não retire as coberturas. • Não utilize este produto antes de montar a base. • Não ligue nem desligue este produto durante uma tempestade eléctrica. • O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente ligada à terra. • Qualquer equipamento ligado a este produto deve estar ligado a tomadas eléctricas devidamente ligadas à terra. • Para isolar o monitor da fonte de a
Résumé du contenu de la page N° 6
T55A.book Page f Saturday, August 29, 1998 10:37 AM VAARA Sähköiskun vaaran välttämiseksi: • Älä avaa laitteen kansia missään tilanteessa. • Älä käytä laitetta, ellei jalustaa ole kiinnitetty. • Älä kytke laitetta pistorasiaan tai irrota sitä pistorasiasta ukonilman aikana. • Virtajohto on kytkettävä asianmukaisesti johdotettuun ja maadoitettuun pistorasiaan. • Kaikki muutkin laitteet, joihin tämä tuote on liitetty, on kytkettävä asianmukaisesti johdotettuihin pistorasioihin. • Kun haluat e
Résumé du contenu de la page N° 7
T55A.book Page 1 Wednesday, September 16, 1998 10:32 AM Contents Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 8
T55A.book Page 2 Wednesday, September 16, 1998 10:32 AM Setup Hardware Requirements This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support XGA 1024 × 768, SVGA 800 x 600, or VGA 640 x 480 at 60 Hz. Workplace Preparation This section gives advice Height on what you should The monitor should be positioned so that the top of the screen is slightly consider before you set up your monitor. below your eye level when you sit at your worksta
Résumé du contenu de la page N° 9
T55A.book Page 3 Wednesday, September 16, 1998 10:32 AM Back You should sit back in your chair and use the backrest. Hands Use a light touch on the keyboard, keeping your hands and fingers relaxed. Allow a space in front of the keyboard to rest your wrists when not typing. Consider using a wristpad. Eyesight Working with monitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly. Screen sett
Résumé du contenu de la page N° 10
T55A.book Page 4 Wednesday, September 16, 1998 10:32 AM Connecting your Monitor Be sure to read the 1. Turn off your PC and all attached devices. ‘Safety Information’ at 2. Connect the signal cable to the video port on the back of your computer. the front of this User Guide before carrying out this This port might be directly attached to your computer (figure A), or it procedure. might be part of a video adapter card (figure B). The video port on your computer or video adapter card may
Résumé du contenu de la page N° 11
T55A.book Page 5 Wednesday, September 16, 1998 10:32 AM Adjusting the Monitor Position Viewing Angle You can tilt the screen backward and forward as shown below. Caring for your Monitor Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows: • Gently wipe the covers and the screen with a soft cloth. • Remove finger marks and grease with a damp cloth and mild detergent; do not use solvents or abrasives. • Never use flammable cleaning m
Résumé du contenu de la page N° 12
T55A.book Page 6 Wednesday, September 16, 1998 10:32 AM Configuring your Monitor Automatic Setup The Setup Utility included When you first use your monitor you must perform Automatic Setup (AUTO on the setup diskette is for SETUP). This procedure sets up your monitor to process the video signals from displaying dot patterns. They do your computer without image discoloration or smearing. After you perform not replace or modify the display driver. AUTO SETUP, the settings are stored and
Résumé du contenu de la page N° 13
T55A.book Page 7 Wednesday, September 16, 1998 10:32 AM Auto Setup for the PC Before carrying out Locate the operating system installed on your PC in the table below and this section, it is very follow the appropriate instructions. You may choose to run AUTO SETUP for important that The Setup each operating system that you use. This means that if you sometimes use Diskette for Windows 95 or your monitor while running any version of Windows and sometimes also use it Windows 98 has been
Résumé du contenu de la page N° 14
T55A.book Page 8 Wednesday, September 16, 1998 10:32 AM Auto Setup for DOS If the monitor is in standby 1. Turn on the monitor first; then the PC. mode (STANDBY ON), it may automatically turn off while If the message CHECK SIGNAL CABLE is displayed, or if nothing is you are waiting for it to warm up. displayed check: If this happens, switch off the • that the video interface cable is connected properly. monitor and switch it on again • the correct video adapter card is installed. after
Résumé du contenu de la page N° 15
T55A.book Page 9 Wednesday, September 16, 1998 10:32 AM Auto Setup for Windows 3.1, Windows 95, Windows 98 or Windows NT If the monitor is in standby 1. Turn on the monitor first; then the PC. mode (STANDBY ON), it may automatically turn off while If the message CHECK SIGNAL CABLE is displayed, or if nothing is you are waiting for it to warm up. displayed check: • that the video interface cable is connected properly. • the correct video adapter card is installed. • the correct supported di
Résumé du contenu de la page N° 16
T55A.book Page 10 Wednesday, September 16, 1998 10:32 AM 10. Press the ESC key to return to Windows. You have completed the monitor setup for Windows. If you use other operat- ing systems, perform the appropriate AUTO SETUP for those systems, also: see Auto Setup OS/2 on page 11 and Auto Setup for DOS on page 8. 10
Résumé du contenu de la page N° 17
T55A.book Page 11 Wednesday, September 16, 1998 10:32 AM Auto Setup OS/2 If the monitor is in standby 1. Turn on the monitor first; then the PC. mode (STANDBY ON), it may automatically turn off while If the message CHECK SIGNAL CABLE is displayed, or if nothing is you are waiting for it to warm up. displayed check: • that the video interface cable is connected properly. • the correct video adapter card is installed. • the correct supported display mode is selected for your PC. 2. Wait appr
Résumé du contenu de la page N° 18
T55A.book Page 12 Wednesday, September 16, 1998 10:32 AM If the screen flickers, 16. When finished, the OSD main menu returns. Press the Exit button repeat the setup several to exit from the OSD. times until the flicker is minimised, or adjust it manually 17. Press the ESCAPE key to return to the OS/2 Window. by following Manual Setup on page 13. You have completed the monitor setup for OS/2. If you use other operating systems, perform the appropriate AUTO SETUP for those systems, al
Résumé du contenu de la page N° 19
T55A.book Page 13 Wednesday, September 16, 1998 10:32 AM Manual Setup Normally, you can complete the setup procedure using AUTO SETUP, however, if your screen image is still distorted after you perform AUTO SETUP or the setup diskette does not run on your system, perform MANUAL SETUP. If the monitor is in standby 1. Have your monitor turned on for about 15 minutes, until the monitor mode (STANDBY ON), it warms up. might automatically turn off while you are waiting for it to 2. Display
Résumé du contenu de la page N° 20
T55A.book Page 14 Wednesday, September 16, 1998 10:32 AM Adjusting Your LCD Monitor User controls User control features Icon Control Description Displays the OSD main menu Exit Exits from menus and sub-menus Exits the OSD Displays the OSD main menu Left Arrow Moves the cursor to highlight icons and other options Displays the OSD main menu Right Arrow Moves the cursor to highlight icons and other options Displays the OSD main menu OSD Enter Enters menus and sub-menus and selects the highl
