Résumé du contenu de la page N° 1
HH191
HSG 1070
HSG XXXX
Résumé du contenu de la page N° 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Résumé du contenu de la page N° 3
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified
Résumé du contenu de la page N° 4
User’s Manual TABLE OF CONTENTS SAFETY NOTICE .................................................................................................. 5 PRECAUTIONS................................................................................................. 5 SPECIAL NOTES ON LCD MONITORS ...................................................... 6 BEFORE YOU OPERATE THE MONITOR ...................................................... 7 FEATURES.................................................
Résumé du contenu de la page N° 5
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment.
Résumé du contenu de la page N° 6
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0
Résumé du contenu de la page N° 7
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @75Hz ® • EPA ENERGY STAR • GP Green Product • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Power Cord
Résumé du contenu de la page N° 8
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged
Résumé du contenu de la page N° 9
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the DVI cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI-D port. 3. Connect the audio cable between the
Résumé du contenu de la page N° 10
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5 ° to 15 °. Monitor Angle Figure.3. NOTES: • Do not touch the LCD screen when you change the angle.
Résumé du contenu de la page N° 11
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to tur
Résumé du contenu de la page N° 12
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange — Power Saving mode. • MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. • Adjust ▲▼: 1. Adjust Brightness and volume when the OSD is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. •【 i 】Bu
Résumé du contenu de la page N° 13
User’s Manual Resolution 640x400@70Hz ↔ 720x400@70Hz 640x400@85Hz ↔ 720x400@85Hz 640x480@60Hz ↔ 720x480@60Hz 1024x768@70Hz ↔ 1280x768@70Hz 1280x768@60Hz ↔1360x768@60Hz 1400x1050@60Hz ↔ 1680x1050@60Hz 1400x1050@RB 60Hz ↔ 1680x1050@RB 60Hz 1400x1050@75Hz ↔ 1680x1050@75Hz 1440x900@60Hz ↔ 1600x900@60Hz ** The screen resolutions available will depend on the purchased model. NOTES: • Do not install the monitor
Résumé du contenu de la page N° 14
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/ CONTRAST Adjust the brightness value of the display according to your preference. Select「BRIGHTNESS」option to adjust the BRIGHTNESS brightness value. Adjust the contrast value of the display according to your preference. Select「CONTRAST」option to adjust the contrast CONTRAST value. Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the X-CONTRAST contrast is
Résumé du contenu de la page N° 15
User’s Manual Select the 「H-POSITION」 option to shift the screen image to the H-POSITION left or right. Enter the option and adjust the level. [For VGA only] Select the 「V-POSITION」 option to shift the screen image up or V-POSITION down. Enter the option and adjust the level. [For VGA only] Select the 「CLOCK」option to reduce the vertical flicker of CLOCK characters on the screen. Enter the option and adjust the level
Résumé du contenu de la page N° 16
User’s Manual To choose the color combination of the OSD window, select 「OSD COLOR」 option under 「OSD SETTING」 menu, choose OSD COLOR modes 1/2/3. SYSTEM While transferring via the HDMI port, it is recommended to set AUDIO INPUT to HDMI; if no sound is outputted, it is AUDIO INPUT recommended to select AUDIO INPUT as PC, and make sure the PC audio output cable is connected to monitor’s LINE IN (or AUDIO IN) port. [For HDMI Input only] Select the 「VOLUME」 option to change the volume
Résumé du contenu de la page N° 17
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID informati
Résumé du contenu de la page N° 18
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position. Power LED is not on *Power Cord should be connected. *Check if the PC system is Plug & Play compatible. *Check if the Video Card is Plug & Play compatible. No Plug & Play *Check if any plug pins on the VGA or DVI connector are bent. The display is too dark or too bright. *Adjust the Contrast and Brightness Controls. Picture bounces
Résumé du contenu de la page N° 19
User’s Manual INPUT as a PC option, and make sure PC audio output cable is connected to monitor’s LINE IN port(or AUDIO IN port). [For HDMI Input only] 19
Résumé du contenu de la page N° 20
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. FACTORY PRESET TIMING TABLE: HORIZONTAL VERTICAL MODE RESOLUTION FREQUENCY (KHz) FREQUENCY (Hz)
