Résumé du contenu de la page N° 1
HS233
HSG 1155
Résumé du contenu de la page N° 2
User’s Manual OSD[4.393] Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. This device complies with requirement of EMC directive 2004/108/EC with regard to Electromagnetic Compatibility, and 73/23/EEC and 93/68/EEC with regard to Low Voltage directive. Socket-outlet shall be near the equipment and shall be accessible. Trademark Notice:
Résumé du contenu de la page N° 3
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified t
Résumé du contenu de la page N° 4
User’s Manual TABLE OF CONTENTS SAFETY NOTICE .................................................................................................. 5 PRECAUTIONS................................................................................................. 5 SPECIAL NOTES ON LCD MONITORS ...................................................... 6 BEFORE YOU OPERATE THE MONITOR ...................................................... 7 FEATURES.................................................
Résumé du contenu de la page N° 5
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment.
Résumé du contenu de la page N° 6
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0
Résumé du contenu de la page N° 7
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES 58,4cm / 23” Wide Screen TFT Color LCD Monitor Crisp, Clear Display for Windows GP Green Product Ergonomic Design Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Cables and User manual Power Cord Warranty Card Quick Start Guide User’s Manua
Résumé du contenu de la page N° 8
User’s Manual INSTALLATION INSTRUCTIONS INSTALL REMOVE Figure.1. Installing and Removing the Base INSTALLATION: 1. Carefully place the monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to prevent any damage to the monitor. 2. Align the base with the opening of the stand. 3. Snap the base into stand. A clear click sound will affirm that the base is connected correctly. 4. Verify that the base is securely attached
Résumé du contenu de la page N° 9
User’s Manual SETTING THE MONITOR ON THE WALL DISSEMBLING THE STAND BASE: 1. Disconnect all the cables and cords from the Monitor to prevent damage. 2. Carefully place the monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to prevent any damage to the monitor. 3. Press the release button as indicated, follow the arrow direction to remove the base. 4. Remove the three (3) screws so that the stand
Résumé du contenu de la page N° 10
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer’s VGA port. 2. Connect one end of the DVI cable to the back of the monitor and connect the other end to the computer’s DVI port. 3. You must use the enclosed dual-link DVI cable for 120 Hz and 3D functionality. 4. Connect one end of the HDMI to DVI cable (optiona
Résumé du contenu de la page N° 11
User’s Manual ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5 to 15 . Monitor Angle Figure.3. NOTES: Do not touch the LCD screen when you change t
Résumé du contenu de la page N° 12
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the Signal cable from the monitor to the VGA card. Press the power button to turn on the monitor. The power indicator will light up. Menu / En
Résumé du contenu de la page N° 13
User’s Manual FRONT PANEL CONTROL Power Button: Press this button to switch ON/OFF of monitor’s power. Power Indicator: Blue — Power On mode. Orange — Power Saving mode. MENU: 1. Turn the OSD menu on. 2. Enter sub menu when OSD menu is ON. Adjust ▲▼: 1. Invalid when the OSD menu is off. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. 【
Résumé du contenu de la page N° 14
User’s Manual HOW TO ADJUST A SETTINGS PICTURE Adjust the brightness value of the display according to your preference. Select「BRIGHTNESS」option to adjust the BRIGHTNESS brightness value. Adjust the contrast value of the display according to your CONTRAST preference. Select「CONTRAST」option to adjust the contrast value. Select the 「H-POSITION」 option to shift the screen image to H-POSITION the left or right. Enter the option and adjust the level. [For VGA only] Select the 「V-PO
Résumé du contenu de la page N° 15
User’s Manual Select the「DCR」option to switch the function On or Off DCR Select the「ECO」option to switch the function On or Off. ECO Select the「SHARPNESS」option to adjust the sharpness of the SHARPNESS display. Set the value from 0 to 100. Select the「OD」option to switch the function On or Off. OD OTHER SETTINGS Select 「LANGUAGE」 option to change the language of the LANGUAGE OSD. Enter the option and select a lan
Résumé du contenu de la page N° 16
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-F
Résumé du contenu de la page N° 17
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position. Power LED is not on *Power Cord should be connected. *Check if the PC system is Plug & Play compatible. *Check if the Video Card is Plug & Play compatible. No Plug & Play *Check if any plug pins on the VGA , DVI or HDMI connector are bent. The display is too dark or
Résumé du contenu de la page N° 18
User’s Manual Addendum related to Windows 7 When you encounter display problem under Windows 7, you need to do the following: 1. Make sure your PC computer (Hardware requirement) can support Windows 7. 2. Make sure your video card can run Windows 7. 3. If your video card can support Windows 7, need to install the latest Win 7 driver of your video card. Suggest to do the following: 1. Install the latest Windows 7 video driver of your video card. 2. Try to use the recommended displ
Résumé du contenu de la page N° 19
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. FACTORY PRESET TIMING TABLE: (V
Résumé du contenu de la page N° 20
User’s Manual (HDMI INPUTS) Primary Video Format Timings MODE RESOLUTION 1 640×480p @ 60Hz 2 720×480p @ 60Hz 3 1280×720p @ 60Hz 4 720×576p @ 50Hz 5 1280×720p @ 50Hz 6 1920×1080i @ 60Hz 7 1920×1080i @ 50Hz Secondary Video Format Timings MODE RESOLUTION 1 1920x1080p @ 25Hz 2 1920x1080p @ 30Hz 3 1920x1080p @ 50Hz 4 1920x1080p @ 60Hz ** We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee the image quality. 20
