Résumé du contenu de la page N° 1
EFT920
EFT920
19 inch Flat CRT Color Monitor
User’s
Manual
by Envision Peripherals, Inc.
www.ENVISIONmonitor.com
Before operating your monitor, please read this
manual thoroughly.
EFT920
1
v1_031004
Résumé du contenu de la page N° 2
For Your Safety EFT920 FCC Statement Notice This equipment has been tested and found to 1. The changes or modifications not expressly comply with the limits for a Class B digital device, approved by the party responsible for pursuant to Part 15 of the FCC Rules. These limits compliance could void the user's authority to are designed to provide reasonable protection operate the equipment. against harmful interference in a residential 2. Shielded interface cables and AC power cord, if install
Résumé du contenu de la page N° 3
For Your Safety EFT920 • The monitor is equipped with a three-pronged Precautions grounded plug, a plug with a third (grounding) • Do not use the monitor near water, e.g. near a pin. As a safety feature, this plug will only fit into bathtub, washbowl, kitchen sink, laundry tub, a grounded power outlet. If your outlet does not swimming pool or in a wet basement. accommodate the three-wire plug, have an electrician install the correct outlet, or use an • Do not place the monitor on an unst
Résumé du contenu de la page N° 4
For Your Safety EFT920 General Notes General Features: • Do not install the monitor near heat sources • 19" (48.3 cm) Color Monitor such as radiators or air ducts. • Crisp, Clear Display for Windows • Do not place monitor in direct sunlight or in • Supports Resolutions up to 1600 X 1200 pixels areas with excessive dust, mechanical vibration @75Hz or shock. ® • EPA ENERGY STAR • Save the original shipping carton and packing materials in case you need to ship your monitor. Be sure to repackag
Résumé du contenu de la page N° 5
Before You Operate the Monitor EFT920 Installing & Removing the Base EFT920 5 v1_031004
Résumé du contenu de la page N° 6
Before You Operate the Monitor EFT920 Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin Caution: Make sure the power cord is the correct connector on the back of your computer and type that is required in your area. This monitor tighten the two screws. has a universal power supply that allows operation in either 100/120V AC or 220/240V AC 2. Connect the power cord into your monitor's voltage areas (no user adjustment is required). power i
Résumé du contenu de la page N° 7
Operating Instructions EFT920 Front Panel Buttons Exit: Press this button to save changes and MENU: Press this button to open the OSD close the OSD window. window or select a highlighted function. Brightness: Press this button to adjust the Power Indicator: A green light indicates picture’s brightness. If the OSD window is that the monitor is on. An orange light open, this button allows you to move within indicates that the monitor is in Off mode. the window and select desired functions. Powe
Résumé du contenu de la page N° 8
Operating Instructions EFT920 Adjusting the OSD Settings 1. Press the MENU button to open the OSD 5. To save and exit, press the EXIT icon or leave window. the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. 2. Press the < or > buttons until the desired function is highlighted. Note: When the OSD window is open, the input signal timing settings appear at the top. 3. Press MENU to open the function’s window. H: stands for horizontal frequency and
Résumé du contenu de la page N° 9
Operating Instructions EFT920 Plug & Play DDC1/2B Feature Windows INF Driver File This monitor is equipped with VESA DDC1/2B Most computers will automatically configure your capabilities according to the VESA DDC monitor to work with your computer. For optimal STANDARD. It allows the monitor to inform the viewing of your monitor, download the Envision host system of its identity and, depending on the monitor driver. level of DDC used, communicate additional information about its display cap
Résumé du contenu de la page N° 10
Technical Support (FAQ) EFT920 Problem Possible Solution Power LED is not ON • Make sure the power button is ON. • Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • Confirm that your computer is Plug & Play compatible. • Confirm that your video card is Plug & Play compatible. • Inspect the video cable and make sure that none of the pins are bent. • Make sure the Envision monitor drivers are installed (ENVISION monitor drivers are av
Résumé du contenu de la page N° 11
Appendix EFT920 Specifications Input Video Red, Green, Blue CRT Size 19.0" (48.3 cm) Analog Interface 11.4” (29 mm) neck Separate H/V TTL Sync. 0.25mm(D), 0.21mm(H) dot pitch H/V Sync. Positive/Negative H-Frequency 30 kHz - 98 kHz 90 degree deflection V-Frequency 50 Hz -160 Hz Viewable image size 18.0” (45.3 cm) Input Video Signal Analog: diagonal 0.7 Vpp, 75 OHM, Positive Preset Display area 13.7” (346 mm) X 10.3” (260 mm) Power Source Universal AC 100 - 240 V Dot Clock 200 MHz 50/60 H
Résumé du contenu de la page N° 12
Appendix EFT920 Specifications (continued) Environmental Operating Temp: Considerations 32° to 104°F (0° to 40°C) ambient Operating Humidity: 10% to 85% Signal Cable Attached Mini D-sub 15 Male Optimal Viewing Mode: 1280 x 1024 @ 85 Hz EFT920 12 v1_031004
Résumé du contenu de la page N° 13
Appendix EFT920 Factory Preset Timing Table Resolution Horizontal Vertical Standard (in pixels) Frequency Frequency VGA 720 × 400 31.5 kHz 70 Hz 640 × 480 31.5 kHz 60 Hz VESA / 85 640 × 480 43.3 kHz 85 Hz 800 × 600 53.7 kHz 85 Hz 1024 × 768 68.7 kHz 85 Hz 1280 × 960 85.9 kHz 85 Hz 1280 × 1024 91.1 kHz 85 Hz VESA / 75 1600 × 1200 93.8 kHz 75 Hz EFT920 13 v1_031004
Résumé du contenu de la page N° 14
Appendix EFT920 Connector Pin Assignment Pin Number Description Pin Number Description 1Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground EFT920 14 v1_031004
