Résumé du contenu de la page N° 1
User’s Manual
Color LCD Monitor
It shall be assured that the final system is in compliance to
IEC60601-1-1 requirements.
Résumé du contenu de la page N° 2
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. • Power supplied equipment can emit electromagnetic waves,
Résumé du contenu de la page N° 3
English TABLE OF CONTENTS PRECAUTIONS ...................................................................................4 1. INTRODUCTION .....................................................................................9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors .............
Résumé du contenu de la page N° 4
English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below). [Location of the Caution Statements] [Symbols on the unit] Symbol Location This sym
Résumé du contenu de la page N° 5
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage. Do not open the cabinet or modify the unit. Opening the cabinet or modifying the unit may result in fire, electric shock, or burn. Refer all servicing to qualified service personnel. Do not attempt to se
Résumé du contenu de la page N° 6
English WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. To disconnect the power cord, grasp the plug firmly and pull. Tugging on the cord may damage and result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. Use the correct voltage. * The
Résumé du contenu de la page N° 7
English WARNING Do not touch a damaged LCD panel directly with bare hands. The liquid crystal which leaks from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor. Follow local regulation or laws for safe disposal. The backlight of the LCD panel contains mercury. CAUTION Handle with care when carrying the unit. Disconnect
Résumé du contenu de la page N° 8
English LCD Panel In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, please use the monitor with the brightness below 160 2 cd/m (BRIGHTNESS approximately 70 %). The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to fl
Résumé du contenu de la page N° 9
English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant (DVI-I connecter x 2) • DVI (p. 48) Digital input (TMDS (p. 49)) compliant • [Horizontal scanning frequency] Analog: 30 - 82 kHz Digital: 30 - 65 kHz [Vertical scanning frequency] Analog: 49 - 86 Hz (1280 x 1024: 49 - 75 Hz) Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz) [Resolution] 1M pixels (1280 dots × 1024 lines) [Frame synchronous mode] 57.5 - 67 Hz su
Résumé du contenu de la page N° 10
English 1-3. Controls & Connectors Front (2) (1) FineContrast Menu Control Panel (3) (4) (5) (6) (7) (8) (9) ® (1) ScreenManager Main Menu (2) Main Power Switch (3) SIGNAL1-2 Input Signal Selection Button *1 (4) MODE Mode Button (5) AUTO Auto Adjustment Button (6) ENTER Enter Button *2 (7) Control Buttons (Left, Down, Up, Right) (8) Power Button *3 (9) Power Indicator Blue Operation Yellow / Power saving Flashing yellow (2 times for each) Flashing yellow slowly Power is of
Résumé du contenu de la page N° 11
English Rear (11) (10) Bottom (13)(14) (12) (15) * 4 (10) Height Adjustable Stand (Detachable) *5 (11) Security Lock Slot (12) DVI-I Input Connector x 2 (SIGNAL 1, SIGNAL 2) (13) USB Upstream Port (x 1) (14) USB Downstream Ports (x 2) (15) Power Connector *4 The LCD monitor has the capability of the Portrait/Landscape display. (The panel pivots in the clockwise direction 90°.) For the Portrait display, use the software for the portrait. The LCD monitor can be used with an
Résumé du contenu de la page N° 12
English 2. CABLE CONNECTION 2-1. Before Connecting Before connecting your monitor to the PC, change the display screen settings (resolution p. 49) and frequency) in accordance with the charts below. NOTE • When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings. Analog Input Resolution Frequency Dot Clock Remarks 640 × 480 ~ 85 Hz 135 MHz VGA, VESA (Max.) 640 × 480
Résumé du contenu de la page N° 13
English 2-2. Connecting the signal cable (For the computer employing D-Sub or DVI connector) NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Power Cord Analog Input Signal Cable Connector PC Signal Cable (FD-C16 Video Output • Standard graphics car
Résumé du contenu de la page N° 14
English Digital Input Signal Cable Connector PC Signal Cable Video Output • Digital graphics board (FD-C35/FD-C39 enclosed) Connector / DVI • Power Mac G4 / G5 (DVI) Input Connector (monitor) / DVI 2. Plug the power cord into the power connector on the rear of the monitor. 3. Lead the power cord and signal cable into the cable holder at rear of the monitor. NOTE • The cables are recommended to lead with slight sag for the smooth motion of the stand and the Portrait/Landscape displa
Résumé du contenu de la page N° 15
English WARNING The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. Not doing so may result in fire or electric shock. 5. Turn on the monitor’s Power Button and then switch on the PC’s power. The monitor’s power indicator will light up (blue). If an image does not appear, refer to the “7. TROUBLESHOOTING” (p.40) for advice. Whenever finished, turn off the PC and the monitor. NOTE • When turning on the monitor, the kind of the
Résumé du contenu de la page N° 16
English 2-3. Connecting the signal cable (For the computer employing ADC) NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Power Cord To Input the Signal Through ADC Signal Cable Connector PC Signal Cable (FD-C35/FD-C39, Video Output Connector/ • P
Résumé du contenu de la page N° 17
English 3. Lead the power cord and signal cable into the cable holder at rear of the monitor. NOTE • The cables are recommended to lead with slight sag for the smooth motion of the stand and the Portrait/Landscape display. Cable Holder 4. Plug the other end of the cord into a power outlet. The monitor’s power indicator will flash yellow slowly. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the
Résumé du contenu de la page N° 18
English 5. Press the power button while pressing the Input Signal Selection button. The Input Selection menu is appeared on the screen. 6. Change SIGNAL 1 (DVI-I Connector) in the Input Selection menu to “ADC”. Press Enter button to complete the setting and the menu closes. 7. Switch on the PC's power. The monitor’s power indicator will light up (blue). If an image does not appear, refer to the “7. TROUBLESHOOTING” (p.40) for additional advice. Whenever finishing your operation, turn off
Résumé du contenu de la page N° 19
English 2-4. Connecting Two PCs to the Monitor Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the back of the monitor. Connecting Examples (SIGNAL 1) (SIGNAL 2) PC 1 PC 2 (Ex.1) Analog D-Sub Signal Cable Signal Cable DVI Digital mini 15 (FD-C16 enclosed) (FD-C35/FD-C39 pin enclosed) (Ex.2) Analog D-Sub Signal Cable Signal Cable D-Sub Analog mini 15 mini (FD-C16 enclosed) (FD-C16 optional) pin 15 pin (Ex.3) Digital DVI Signal Cable Signal Cable DVI D
Résumé du contenu de la page N° 20
English The Priority Input Signal This function is used to select which PC will have priority to control the monitor when utilizing two PCs. The monitor constantly checks the input signals and switches automatically in accordance with the “Input Priority” setting (see table below). Once a priority is set, whenever a change of signal is detected at the selected input, the monitor will switch the input to that signal. In the case of only one signal being present at either input, the monito
