Résumé du contenu de la page N° 1
INSTRUCTION MANUAL
DP-SP22
DP-SP21
DP-SP20
S
PLASMA MONITOR (DISPLAY)
P
E
SPEAKER
A
K
E
R
Thank you for purchasing the Daewoo Electronic Plasma Display Speakers. These
speakers are specifically designed only for the Daewoo Plasma Display. To ensure the
safe operation of the unit, please read these instructions before installing.
Résumé du contenu de la page N° 2
TABLE OF CONTENTS ............................ 1. Check for enclosed parts 2 ...................... 2. Important Safety Instructions 3 ................................. 3. Assembly Instructions 5 1) Using speakers when attached to the plasma display 2) Using speakers on its own stand 1
Résumé du contenu de la page N° 3
PLASMA DISPLAY SPEAKER SPEAKER 1. PLEASE CHECK THE FOLLOWING ITEMS SHOWN BELOW (2) M5 SCREWS VIBRATION ABSORBENT SPONGE S P E A K (2) (16) E R SPEAKER WIRES SPECIAL SCREWS / ROUND HEAD SCREWS (2) (4) STAND FIXED BRACKETS (2) (4) 2
Résumé du contenu de la page N° 4
2. IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. CAUTION Do not leave out any part when assembling. Do not use any parts other than those Please install all parts as
Résumé du contenu de la page N° 5
PLASMA DISPLAY SPEAKER PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING * When assembling, be sure to use the enclosed Please be careful not to stain the speakers with parts and make sure all parts are tightly any gas or oil. screwed as instructed. (Failing to do so will cause the speakers to (Doing so will change the outer appearance) vibrate and unable to produce clear sound.) S Do not place the speakers in a humid or dusty Do not place the speakers near heating units. P plac
Résumé du contenu de la page N° 6
3. ASSEMBLING INSTRUCTIONS USING SPEAKERS WHEN ATTACHED TO THE PLASMA DISPLAY ATTACHING VIBRATION ABSORBENT SPONGES TO SPEAKERS 1 . . Clean the surface with soft, lint-free cloth Attach the sponge to the side of the where sponges will be attached. speaker that will be attached to the plasma display. 5mm Note Please leave a 5 mm space on the top and bottom when attaching. Do not cover the entire side with the sponge as shown in the picture above. 5mm INSTALLING FIXED BRACKETS TO SPEAKERS 2 .
Résumé du contenu de la page N° 7
PLASMA DISPLAY SPEAKER INSTALLING SPEAKERS TO THE PLASMA DISPLAY 3 . Place a protective covering over the surface you will be working on and lay the plasma display as shown below. S P E A K E R . Take the speakers with fixed brackets to the back of the plasma display. Place the hooks onto the fixed brackets to the squared holes in the back of the plasma display. Hooks . Now tightly secure the hooks with the M5 screws. Note . Please be sure to secure the screws to avoid any shaking or loosene
Résumé du contenu de la page N° 8
CONNECTING SPEAKER WIRES 4 . Take the speaker wire(2) and use the red cord to connect to and fro (+) inputs, and use the black cord to connect to and fro (-) inputs. Note . Please be sure to connect red cord with (+) and black with (-); otherwise, speakers will not produce clear sounds. . Please retain the left over accessories. 7
Résumé du contenu de la page N° 9
PLASMA DISPLAY SPEAKER USING SPEAKERS ON ITS OWN STAND INSTALLING SPEAKERS TO ITS OWN STAND. 1 Please be sure to have the vibration absorbent sponge onto the side of . Use a coin to secure the speaker where the the special screws S stand will be attached. Coin (round head screws) P tightly. E A Stand K E R Note . To avoid loose fitting, please be sure that screws are secured tightly. Otherwise, vibrating or distorted sounds may be produced. CONNECTING SPEAKER WIRES. 2 . Take the speaker wire
