Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Safety ........................................................................................................................................................................ 4 National Conventions ......................................................................................................................................... 4 Power .......................................................................................................................................................
Résumé du contenu de la page N° 3
EPEAT Declaration .......................................................................................................................................... 60 Service .................................................................................................................................................................... 61 Warranty Statement for Europe........................................................................................................................ 6 1 Warrant
Résumé du contenu de la page N° 4
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential dam
Résumé du contenu de la page N° 5
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an
Résumé du contenu de la page N° 6
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care. Never push any
Résumé du contenu de la page N° 7
7
Résumé du contenu de la page N° 8
Cleaning Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. Other If the product is emitting a strange smell, sound or smoke, disconnect the power
Résumé du contenu de la page N° 9
Résumé du contenu de la page N° 10
Setup Stand & Base Please setup or remove the base following the steps as below. Setup: Remove: 10
Résumé du contenu de la page N° 11
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from 4° to 14 °. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. 11
Résumé du contenu de la page N° 12
Connecting the Monitor Cable Connections On Back of Monitor and Computer: 5 4 1 3 2 1. Power 2. Audio 3. Analog (DB-15 VGA cable) 4.DVI 5.HDMI To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect the audio cable to audio in port on the back of the monitor. 3 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
Résumé du contenu de la page N° 13
Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1 Rem ove the base. 2 F ollow the manufacturer's instructi ons to assemble the wall mounting arm. 3 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4 Insert the 4 screws into the holes and
Résumé du contenu de la page N° 14
Adjusting Setting Optimal Resolution Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization 14
Résumé du contenu de la page N° 15
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 15
Résumé du contenu de la page N° 16
Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. 16
Résumé du contenu de la page N° 17
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. 1920 1080 Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 17
Résumé du contenu de la page N° 18
Hotkeys ECO(DCR)/i-care/up Volume/Left 4:3 or Wide / Right Source(Auto) / down Power Key Press the Power button continuously about 2 second to turn off the monitor. Eco Mode/DCR/i-care hot key Press the Eco key continuously to select the Eco mode of brightness and DCR on when there is no OSD ( Eco mode hot key may not be available in all models). i-care can detect the intensity of surrounding lights and automatically adjusts the monitor brightness according to different light i
Résumé du contenu de la page N° 19
OSD Setting Basic and simple instruction on the control keys. 1) Press Menu (Power) button to activate the OSD window. Press left, right, up, down button to navigate through the functions. Once the desired function is highlighted, press Menu (Power) button to activate submenu . 2) In sub-menu, Press up, down button to navigate through the functions. Once the desired function is highlighted, press left, right button to change the setting. Press Menu (Power) button to return to
Résumé du contenu de la page N° 20
Luminance Press (Menu) to display menu. Press (Left/Right/Up/Down) to select (Luminance),and press to enter. Press (Up/Down) to select submenu, and press (Left/Right) to adjust. Press to exit. 20
