Résumé du contenu de la page N° 1
L CD Monitor User Manual
I23 67F /I2267
FWH/
/ /I2067F
I2367F I2267FW
LED Backlight
Résumé du contenu de la page N° 2
Safety ........................................................................................................................................................................ 3 National Conventions ......................................................................................................................................... 3 Power .......................................................................................................................................................
Résumé du contenu de la page N° 3
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential dam
Résumé du contenu de la page N° 4
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an
Résumé du contenu de la page N° 5
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care. Never push a
Résumé du contenu de la page N° 6
Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. 6
Résumé du contenu de la page N° 7
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. 7
Résumé du contenu de la page N° 8
Setup Contents in Box Monitor * Base Adapter Audio Cable CD Manual * * * Analog Cable HDMI Cable Power Cable DVI C able and HDMI cables) will be provided for all countries and regions. Please Not all signal cables (Analog, check with the local dealer or AOC branch office for confirmation. 8
Résumé du contenu de la page N° 9
Setup Stand & Base Please setup or remove the base following the steps as below. Setup: 2 1 Remove: 9
Résumé du contenu de la page N° 10
Unit standing without base is available. (Caution: must put unit in flat surface. Any uneven or sloped surface may result unit damaged or injury to user.) 10
Résumé du contenu de la page N° 11
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 23 °. -5 23 NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. 11
Résumé du contenu de la page N° 12
Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1 2 3 4 5 1. Power 2. Earphone 3. Audio 4 . D-Sub 5. HDMI To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the 15-pin D-Sub/HDMI cable to the back of the monitor and connect the other end to the computer's D-Sub/HDMI port. 3 Turn on your monitor and computer. If yo
Résumé du contenu de la page N° 13
Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1 2 3 1. Power 2. D-Sub 3. DVI To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the 15-pin D-Sub/DVI cable to the back of the monitor and connect the other end to the computer's D-Sub/DVI port. 3 Turn on your monitor and computer. If your monitor displays an image, insta
Résumé du contenu de la page N° 14
Adjusting Setting Optimal Resolution Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization 14
Résumé du contenu de la page N° 15
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to . Optimal preset resolution . 15
Résumé du contenu de la page N° 16
Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. 16
Résumé du contenu de la page N° 17
6 Click SETTINGS. Optimal preset resolution 7 Set the resolution SLIDE-BAR to Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to . Optimal preset resolution 17
Résumé du contenu de la page N° 18
Hotkeys 1 2 3 4 5 1 1 Menu/Enter Menu/Enter 2 Volume/∧ 2 4:3 or wide /∧ 3 3 Eco (DCR) Eco (DCR)/ ∨ / ∨ 4 4 Source/Auto/Exit Source/Auto/Exit 5 Power 5 Power Power Press the Power button to turn on/off the monitor. Eco (DCR) ∨ Press the Eco key continuously to select the Eco mode of brightness and DCR on when there is no OSD. (Eco mode hot key may not be available in all models). ∧
Résumé du contenu de la page N° 19
OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press∧or ∨ to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it . pr ess or to navigate through the sub-menu functions. Once the desired ∧ ∨ function is highlighted, press MENU-button to activate it. 3) Press∧ or ∨to change the settings of the selected function. Press AUTO to exit. I f you want to
Résumé du contenu de la page N° 20
Luminance 1. Press MENU (Menu) to display menu. 2. Press or to select (Luminance), and press MENU to enter. ∧ ∨ ∧ ∨ 3. Press or to select submenu, and press MENU to enter. 20
