Résumé du contenu de la page N° 1
SyncMaster 797MB/997MB
Résumé du contenu de la page N° 2
Main Page On -Screen Display Safety Instru ctions Troubleshooting Notationa l Check List Power Q & A Installation Self -Test Feature Check Clean Oth er Intro ductio n Specifications Unpacking Ge nera l Spe cificatio ns Front PowerSaver Rear Preset Timin g Mode s Bottom Setup Information Connecting the Monitor Service Installing the Monitor Driver Terms Automatic Regulato ry Manual Natural Color Base Installat ion Authority
Résumé du contenu de la page N° 3
Notational Power Installation Clean Oth er Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Résumé du contenu de la page N° 4
When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long Notationa l periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Power Installation Clean Do not use a damaged or loose plug. Oth er This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the
Résumé du contenu de la page N° 5
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Notationa l Power Installation Clean Put your monitor in a location with low humidity and a minimum of Oth er dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It cou
Résumé du contenu de la page N° 6
When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. Notationa l Power (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The Installation antiglare/anti-static surface coating on the CDT may also be affected.) Clean Oth er Dilute the detergent (1:10 ratio) with water before using. Do not
Résumé du contenu de la page N° 7
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notationa l Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This may cause
Résumé du contenu de la page N° 8
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.
Résumé du contenu de la page N° 9
SyncMaster 797MB Monitor and Stand Power Cord Unpacking Front Stand Rear Bottom Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD
Résumé du contenu de la page N° 10
SyncMaster 997MB Monitor and Stand Power Cord Unpacking Front Stand Rear Bottom Signal Cable (Option) (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Quick Setup Guide Warranty Card (Not available in all locations) User's Guide and Driver Installation CD
Résumé du contenu de la page N° 11
Unpacking Front Rear Bottom 1. Menu button Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 3. Enter button Used to select the OSD menu. 4. Power button Use this button for turn the monitor on and off. 5. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. Note: See PowerSaver described in the manual for
Résumé du contenu de la page N° 12
Ge nera l BNC Conne cto rs (Option) General SyncMaster 797MB/997MB Unpacking Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. BNC Connectors (Option) SyncMaster 997MB (The configuration at the back of the monitor may vary from p
Résumé du contenu de la page N° 13
Unpacking Front Rear Bottom 1. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
Résumé du contenu de la page N° 14
Ge nera l BNC Conne cto rs (Option) Connecting General the Monitor SyncMaster 797MB/997MB Installing the Monitor Driver Base Installat ion 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pin
Résumé du contenu de la page N° 15
pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4. When you use a BNC connector. Connect the signal cable to the BNC signal port on the back of your monitor/computer. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Résumé du contenu de la page N° 16
Connecting Your When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor included with this monitor. Driver installation is slightly different from one operating Installing the system to another. Follow the directions as appropriate for the operating system you Monitor Driver have. Base Installat ion Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (WorldWide)
Résumé du contenu de la page N° 17
4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Résumé du contenu de la page N° 18
Wind ows XP Wind ows 200 0 Wind ows Me Wind ows NT Lin ux | | | | Connecting Your Monitor Installing the When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor Driver included with this monitor. Driver installation is slightly different from one operating Base Installat ion system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here.
Résumé du contenu de la page N° 19
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next " button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
Résumé du contenu de la page N° 20
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Cli
