Résumé du contenu de la page N° 1
Mac Pro
Front Panel Board Cable
Replacement Instructions
Note: Follow these instructions carefully. Failure to do so could damage your equipment and
First Steps
void its warranty.
1 Shut down computer.
2 Wait 10 minutes.
Warning: Parts inside
computer can be very
hot. Allow computer
to cool down before
continuing.
3 Unplug all external
cables except power
cord.
4 Touch metal PCI cover
on back of computer.
5 Unplug power cord.
Opening the
Computer
1 Hold side access
panel and lift lat
Résumé du contenu de la page N° 2
Required Tools • Phillips #2 screwdriver • RIght-angle, 2.5 mm hex driver • Flatblade screwdriver • Long-handled Phillips #1 screwdriver Removing the Installed Cable Before removing the front panel board cable, you must remove: • Hard drive in far-left drive bay • Graphics card in slot 1 • Processor tray • PCIe fan • Processor cage Hard Drive 1 Make sure latch on back panel is up, so that drive is unlocked. 2 Pull hard drive out of far-left drive bay. © 2009 Apple Inc. All rights rese
Résumé du contenu de la page N° 3
Graphics Card 3 Locate graphics card in slot 1. 4 Using Phillips #1 screwdriver, loosen 2 captive screws securing card’s bracket to enclosure. 5 Remove bracket from enclosure. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 3
Résumé du contenu de la page N° 4
Note: Card is held in place by retention bar. Following two steps explain how to release bar. 6 Press button on PCIe fan. 7 Move fan to left, which releases retention bar. Note: Some graphics cards require 1 or 2 booster cables connecting card to auxiliary power connectors on backplane board. If your card has booster cables, disconnect them from backplane board. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 4
Résumé du contenu de la page N° 5
8 Holding card by top corners, pull it up out of slot. 9 Remove card from computer. Checklist for handling card: • When removing or installing card, handle it only by the edges. Do not touch its connectors or any components. • Don’t rock card from side to side; instead, lift card straight up from connecotr to remove it, and press card straight into slot to install it. • Don’t force card. If you meet a lot of resistance, pull card out. Check connector and slot for damage or obstructions,
Résumé du contenu de la page N° 6
Processor Tray 10 Locate processor tray. 11 Press down and release 2 latches on front of processor tray. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 6
Résumé du contenu de la page N° 7
12 Holding tray by latches, lift it out of computer. 13 Place tray DIMM side up on soft, clean cloth. PCIe Fan 14 Locate PCIe fan. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 7
Résumé du contenu de la page N° 8
15 Remove 2 screws. 16 Slide fan up and out of computer. Processor Cage 17 Locate processor cage. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 8
Résumé du contenu de la page N° 9
18 Disconnect 3 cables from logic board. 19 Using long-handled Phillips #1 screwdriver, loosen 6 captive screws. 20 Rotate computer to stand vertically. Using 2.5 mm hex driver, remove 5 mushroom- head screws. Note: Processor cage includes two fans, one at each end of cage. Before removing cage from enclosure, you must release 2 latches on each fan and push fans partway into cage. 21 To release 2 latches holding front fan to cage, press down on bottom of cage while using flatblade
Résumé du contenu de la page N° 10
24 Lift cage out of enclosure. Front Panel Board Cable 25 Locate front panel board cable. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 10
Résumé du contenu de la page N° 11
26 Disconnect cable from front panel board and backplane board. 27 Remove cable from enclosure. Installing the Replacement Cable 1 Connect replacement cable to front panel board and backplane board. © 2009 Apple Inc. All rights reserved. 073-1257 Rev. A 11
Résumé du contenu de la page N° 12
Processor Cage Important: Before you re- install cage into enclosure, fans must be inserted partway into cage. 2 Position cage in enclosure. 3 Slide front and rear fans into place, so that they engage with latches. 4 Replace and tighten 5 mushroom-head screws. 5 Secure 6 captive screws. 6 Reconnect 3 cables. PCIe Fan 7 Slide fan into enclosure so that fan tabs engage with slots on metal cage. 8 Press down until fan clicks into place in connector. 9 Replace 2 screws. © 2009 Apple In
Résumé du contenu de la page N° 13
Processor Tray 10 Holding tray by latches, lower it into processor cage. 11 Make sure latches are closed flush with front of processor tray. Graphics Card 12 Reinstall graphics card in slot 1. Note: Align card’s connector with expansion slot and press down until connector is inserted all the way into slot. If installing a 12-inch card, make sure card engages correct slot in PCIe card guide. 13 If card includes booster cables, reconnect cables. 14 Slide PCIe fan to the right to l
Résumé du contenu de la page N° 14
Hard Drive 16 Replace hard drive in far-left drive bay. Closing the Computer 1 Replace access panel. Note: Make sure latch is up before you replace panel. If latch is down, panel will not seat correctly. 2 Push latch down to close and secure access panel. Warning: Never turn on computer unless all its internal and external parts are in place and it is closed. Operating computer when open or missing parts can cause damage or injury. Apple Inc. © 2009 Apple Inc. All rights reserv
