Résumé du contenu de la page N° 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-R1612
CD-RW/DVD-ROM COMBO DRIVE
USER MANUAL
Résumé du contenu de la page N° 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................2 Using the Combo Drive...........................................................3 Troubleshooting.......................................................................5 Specifications ..........................................................................6 Drive Connectors.................
Résumé du contenu de la page N° 3
INTRODUCTION – SD-R1612 General Features CD-R/CD-RW disc write/rewrite at 52X/32X 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD-ROM/CD-R 95ms CD-RW 110ms DVD-ROM - Single 110ms DVD-ROM - Dual 130ms DVD-RAM 200ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM and DVD-ROM discs Regionalization (RPC2 compliance) (DVD) BUS Interface - ATAPI Media Compatibility CD • 650MB CD-ROM (Read) •
Résumé du contenu de la page N° 4
Types of Disc Formats Support – Read DVD: • DVD-ROM (Book 1.02) • DVD-video (Book 1.1) • DVD-R (Book 1.0, 3.9G) • DVD-R (Book 2.0, 4.7G) - General & Authring • DVD+R (Version 1.0) • DVDRW • DVD-RAM CD: • CD-DA (Red Book) • CD-ROM (Yellow Book Mode1&2) • CD-ROM XA (mode 2 Form 1&2) • CD-I (Green Book, Mode2 Form 1&2, Ready, Bridge) • CD-EXTRA/CD-Plus (Blue Book) • CD-R (Orange Book Part II) • CD-RW: HSRW (Orange Book Part III Volume1&2, USRW) Front Panel Figure 1.SD-R1612 D
Résumé du contenu de la page N° 5
SETUP – SD-R1612 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the Combo drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures drive as Slave MA Configure
Résumé du contenu de la page N° 6
Placing Combo Drive inside your Computer Now that you have set the jumpers, you are ready to install your Combo drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the Combo drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshiba Combo drive can be placed i
Résumé du contenu de la page N° 7
Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Toshiba's Combo drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the Combo drive (see Combo drive Back Panel photo for location). Refer to the in
Résumé du contenu de la page N° 8
USING THE DVD Combo Drive – SD-R1612 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc or into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close. Inserting a Disc - Vertically To insert a disc in a drive that is mounted verti
Résumé du contenu de la page N° 9
Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the Combo drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Slide disc holders away from disc. 3. Grasp disc by edges, and lift out of loading tray. 4. Press Eject Button again to close Loading Tray. Software When you purchase the SD-R1612 as a Kit, it will include Nero6 OEM Suite Software, which is used to create CDs and view DVDs. Usage Guidelines • Keep the
Résumé du contenu de la page N° 10
Emergency Ejection CAUTION: The following procedure is intended only as a last resort when pressing the eject button fails to open the Loading Tray 1. Turn computer power OFF by properly shutting down system. 2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in until loading tray opens. Pull tray out. Figure 3.Using Emergency Eject Handling Media DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD mo
Résumé du contenu de la page N° 11
TROUBLESHOOTING – SD-R1612 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). • Are the drive configuration jumpers on the Combo drive set properly? • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the Combo drive
Résumé du contenu de la page N° 12
SPECIFICATIONS –SD-R1612 General Interface ATAPI Formats for Writing Disc at once, Track at once, session at once, Variable & Fixed Packet Write Format Compatibility: CD CD-DA (Red Book) CD-ROM (Yellow Book, Mode 1&2) CD-ROM XA (Mode 2, Form 1&2) CD-I (Green book, Mode 2, Form 1&2, Ready, Bridge) CD-Extra/CD-Plus (Blue Book) Video CD (White Book) CD-R (Orange Book Part II) CD-RW: HSRW (Orange Book Part III, Volume 1&2) US-RW Format Compatibility: DVD DVD-ROM (Book 1.02) DVD-
Résumé du contenu de la page N° 13
Performance Transfer Rate DVD (Single) 21,600KB/second DVD (Dual) 13,500KB/second CD 7,800KB/second (mode 1) CD-R/RW 6,000KB/second (mode 1) Random Access Time CD-ROM, CD-R 95ms CD-RW 110ms DVD Single 110ms DVD Dual 130ms DVDR/RW 130ms DVD-RAM 200ms Data Buffer 2MB Environmental Temperature Operating 0° to 50° C (32° to 122° F) Storage -40° to 65° C (-40° to 149° F) Relative Humidity Operating 10% to 85% Storage/Shipping 10% to 95% Shock (Non-operating) 2ms [200
Résumé du contenu de la page N° 14
Connectors DC input 4-pin Power Supply Connector ATAPI Interface Connector 40 Pin I/F ATAPI Standard Audio Connectors 4-pin and 2-pin connector (use matching housing, Part No. 70066, made by Molex Corp, or equivalent) Regulatory The SD-R1612 Combo drive has been certified by the following regulatory agencies: • UL 1950 • CSA C22.2 No. 950 • TUV (EN60950I) • CE standard • DHHS 21 CFR Sub-Chapter J • FDA CFR21, EN60825 12
Résumé du contenu de la page N° 15
DRIVE CONNECTORS –SD-R1612 Figure 1.SD-R1612 Combo Drive Rear Panel - Connectors Power Power is supplied to your Combo drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered Connector edges, so the power connector fits only one way. CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Audio Supplies Analog and Digital sound to you
Résumé du contenu de la page N° 16
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN I/O SIGNAL HOST SIGNAL NAME PIN I/O SIGNAL HOST SIGNAL NAME NO. NAME NO. NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 - GND 3 I/O HD7 Host Data Bus BIT 7 23 I HWR-,STOP Host I/O Write 4 I/O HD8 Host Data Bus BIT 8 24 - GND 5 I/O HD6 Host Data Bus BIT 6 25 I HRD-, Host I/O Read HDMARDY, - HSTROBE 6 I/O HD9 Host Data Bus BIT 9 26 - GND 7 I/O HD5 Host Data Bus BIT 5 27 O IORDY, I/O Channel Ready
