Résumé du contenu de la page N° 1
ULTRA ATA/133 PCI RAID Card RC200
User Manual
Résumé du contenu de la page N° 2
ULTRA ATA/133 PCI RAID Card RC200 User Manual Contents Feature and benefits 3 System requirement 3 Package contents 3 Hardware installation 4 Device connection 5 Important message for user 7 RAID introduction RAID 0 7 RAID 1 9 RAID 0+1 12 Driver installation 13 Quick guide 14 Detail guide 21 2
Résumé du contenu de la page N° 3
ULTRA ATA/133 PCI RAID Card RC200 User Manual Features and Benefits Silicon Image SiI 0680 Compliant with UltraDMA6 ATA/133 specifications Compliant with PCI v2.2 Plug-n-Play Provides two independent Ultra ATA channels Full ACPI power management support Supports Ultra DMA 0-6 and Multi-word DMA 0-2 Supports hard drives larger than 137GB Supports RAID 0(Striping), RAID1(Mirroring) and RAID 0+1 (Mirror+Striping) CRC(Cyclical Re
Résumé du contenu de la page N° 4
ULTRA ATA/133 PCI RAID Card RC200 User Manual Hardware Installation 4
Résumé du contenu de la page N° 5
ULTRA ATA/133 PCI RAID Card RC200 User Manual Note: For proper operation of the Ultra ATA 133 PCI RAID card, the jumper must remain on. 1. Turn Off the power to your computer and any other connected peripheral devices. 2. Unplug the power cord from the back of the computer. 3. Remove your computer’s cover. 4. Remove the slot bracket from an available PCI slot. 5. To install the card, carefully align the card’s bus connector with the se
Résumé du contenu de la page N° 6
ULTRA ATA/133 PCI RAID Card RC200 User Manual In any given RAID set, it’s best to install the hard drives on separate channels, either Master to Master or Slave to Slave. For example, if you are setting up a RAID set with two hard drives, install the first drive on IDE1 as Master and the second on IDE2 as Master. Use the same concept for multiple hard drives. Note: Only the 40-pin/80-wire UltraATA cable can achieve hard disk UDMA 133 perf
Résumé du contenu de la page N° 7
ULTRA ATA/133 PCI RAID Card RC200 User Manual 4. Reconnect the system power and other peripherals to your computer. Important message for user 1. Backup all your data in HD before setting any RAID. 2. New HD connecting to RC-200 is recommended to “initial” and “format” before setting a RAID. Otherwise, PC might find nothing in the system. 3. Please read the PDF file of “SATARAID5-UserGuide_v1.40” for basic RAID knowledge. 4. If you wa
Résumé du contenu de la page N° 8
ULTRA ATA/133 PCI RAID Card RC200 User Manual For Manual Setup 1. As the BIOS boots press F3 when prompted to enter the RAID BIOS. 2. At the next screen press F2 to form a RAID set. 3. Press F1 to create RAID 0. 4. Choose the chunk size to be used in the RAID set(64 is recommended). 5. Choose the number of hard drives in your stripe set. 6. Assign the hard drives to be used. For optimal performance, alternate hard drives from separate
Résumé du contenu de la page N° 9
ULTRA ATA/133 PCI RAID Card RC200 User Manual RAID 1 (Mirror ) For Manual Setup ＊For New/Blank Hard Drives Recommended for all fresh HD without data. 1. As the BIOS boots press F3 when prompted to enter the RAID BIOS. 2. At the next screen press F2 to from a RAID set. 3. Press F2 to create RAID 1. In a Mirror set the source drive needs to be equal to or smaller than the destination drive. For optimal performance the source drive and
Résumé du contenu de la page N° 10
ULTRA ATA/133 PCI RAID Card RC200 User Manual 5. Assign Source drive, then assign Destination drive. 6. Press Y to copy from Source to Destination drive. 7. Press N to Offline copy. 8. Answer Y to enable Auto-Rebuild. 9. When asked Are You Sure?, press Y to accept. 10. Press ESC to exit the RAID BIOS. For Auto Setup ＊Use this setup on New/Blank hard drives only. 1. As the BIOS boots press F3 when prompted to enter the RAID BIOS. 2.
Résumé du contenu de la page N° 11
ULTRA ATA/133 PCI RAID Card RC200 User Manual 4. Press Y to confirm your choice. The spare drive will be created and listed as the last set. 5. Press ESC to exit the RAID BIOS. 6. The SPARE drive will not be seen by Windows, however, it remains in the background waiting to rebuild the mirror in the event of a hard drive failure. Rebuilding a Failed Mirror Set If a SPARE drive was not configured, the steps below will guide you in rebuil
Résumé du contenu de la page N° 12
ULTRA ATA/133 PCI RAID Card RC200 User Manual 15. Answer Y to enable Auto-rebuild. 16. When asked Are You Sure?, Press Y to accept. 17. Press ESC to exit the RAID BIOS and reboot the computer. RAID 0+1 (Mirror+Striping) This RAID array to be used on New/Blank hard drives only, striping destroys existing data on the hard drive. RAID 0+1 requires at least four hard drives. For Manual Setup 1. As the BIOS boots press F3 when prompted
Résumé du contenu de la page N° 13
ULTRA ATA/133 PCI RAID Card RC200 User Manual For Auto Setup 1. As the BIOS boots press F3 when prompted to enter the RAID BIOS. 2. Press F2 to create a RAID set. 3. Press F3 to create a Mirrored-Striped set. 4. Press A to Auto configure. 5. Press Y to accept the configuration. 6. Press ESC to reboot. 7. Continue with FDISK and FORMAT steps as if you were installing a conventional hard drive. Rebuilding a Failed RAID 0+1 Set The st
Résumé du contenu de la page N° 14
ULTRA ATA/133 PCI RAID Card RC200 User Manual Deleting RAID Arrays 1. As the BIOS boots press F3 when prompted to enter the RAID BIOS. 2. Press F1 to dissolve a RAID set. 3. Enter the number of the RAID set to be deleted. 4. Answer Y to remove the RAID set. 5. Press ESC when finished to reboot. Resolving Conflicts If after a disk failure, the replacement disk was previously part of a RAID set (or used in another system), it may have
Résumé du contenu de la page N° 15
ULTRA ATA/133 PCI RAID Card RC200 User Manual HD connecting to RC-200 instead of motherboard. Please follow below steps a~f to complete the installation. a. Put the driver (the driver must fit the OS you want to install to the HD) into a floppy disk and keep it in the floppy drive. b. Plug the HD. Turn on PC and press F3 to complete the RAID set. After you complete, save and left the setting. c. Inset Windows installation disk and start
Résumé du contenu de la page N° 16
ULTRA ATA/133 PCI RAID Card RC200 User Manual shows as the following picture. C Choose the correct OS for your future system. 16
Résumé du contenu de la page N° 17
ULTRA ATA/133 PCI RAID Card RC200 User Manual If below screen happens, please choose “Standard PC with C-Step i486”. 17
Résumé du contenu de la page N° 18
ULTRA ATA/133 PCI RAID Card RC200 User Manual Keep the floppy disk in floppy drive. PC will notice you as below if you take it off from the drive. 18
Résumé du contenu de la page N° 19
ULTRA ATA/133 PCI RAID Card RC200 User Manual The installation of RC-200 by floppy drive will be completed and the system will detect the HD which now plug on the card. After you install RC-200 successfully by floppy disk, installation will lead you back to the same screen as below and then press “enter” to left the setting. 19
Résumé du contenu de la page N° 20
ULTRA ATA/133 PCI RAID Card RC200 User Manual f. Once the system can find the HD connecting to RC-200, you can follow the normal steps to complete the Windows installation. 3. If you want to create a mirror with a HD with existing OS and a fresh HD, the data on existing HD will copy to fresh HD and boot as RAID 1. In addition, based on the above situation, if a bootable HD on the RC200 is desired. It means in this case you will boot our
