Résumé du contenu de la page N° 1
H8/3834 Series, H8/3814 Series,
H8/3877 Series
FP-100A
User System Interface Cable
(HS3834ECF61H)
for E6000 Emulator
User’s Manual
Rev. 4.0
4/1/03
Renesas Technology Corp.
HS3834ECF61HE(D)
Résumé du contenu de la page N° 2
Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice.
Résumé du contenu de la page N° 3
Preface Thank you for purchasing this user system interface cable (HS3834ECF61H) for the Renesas’s original microcomputer H8/300L series. The HS3834ECF61H is a user system interface cable that connects an H8/300L series E6000 emulator (HS3L08EPI60H; hereinafter referred to as the emulator) to the IC socket for a FP-100A package for the H8/3834 series, H8/3814 series, or H8/3877 series MCU on the user system. The H8/3834 series, H8/3814 series, and H8/3877 series MCUs can be emulated using
Résumé du contenu de la page N° 4
Contents Section 1 Configuration....................................................................................1 Section 2 Connection Procedures......................................................................3 2.1 Connecting User System Interface Cable to Emulator Station .........................................3 2.2 Connecting User System Interface Cable to User System ................................................5 2.2.1 Installing IC Socket ..........................
Résumé du contenu de la page N° 5
Section 1 Configuration CAUTION Use an IC149-KS-11113-0 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-100A package IC socket on the user system. Figure 1 shows the configuration of the HS3834ECF61H user system interface cable for the FP-100A package. Figure 1 HS3834ECF61H User System Interface Cable 1
Résumé du contenu de la page N° 6
Table 1 lists the HS3834ECF61H components. Please make sure you have all of these components when unpacking. Table 1 HS3834ECF61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP-100A package 4 Socket cover 1 For installing an FP-100A-packaged MCU 5 Screws (M2.5 x 11 mm) 2 For fastening cable head (with two flat washers) 6 Documentation 1 User’s manual for HS3834ECF61H (this manual) 2
Résumé du contenu de la page N° 7
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before c
Résumé du contenu de la page N° 8
Figure 2 Connecting User System Interface Cable to Emulator Station 4
Résumé du contenu de la page N° 9
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. To connect the cab
Résumé du contenu de la page N° 10
2.2.4 Fastening Cable Head CAUTION 1. Use a Philips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or a socket contact error may be caused by a crack in the socket sold
Résumé du contenu de la page N° 11
Figure 3 Connecting User System Interface Cable to User System 7
Résumé du contenu de la page N° 12
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Figure 4 Fastening Cable Body 8
Résumé du contenu de la page N° 13
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-100A package (IC149-KS-11113-0: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewhat different from those of the actual chip's mount pad. 27.4 (min.) 21.4 (max.) 0.65 x 29 = 18.85 – 0.1 + 0.1 0.35 0.65 – 0.05 - 0.05 Unit: mm Figure 5 Recommended Dimensions for Mount Pad
Résumé du contenu de la page N° 14
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10
Résumé du contenu de la page N° 15
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11
Résumé du contenu de la page N° 16
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or a socket contact error may be caused by a crack in the socket solde
Résumé du contenu de la page N° 17
Section 4 Verifying Operation 1. When using the H8/300L series E6000 emulator (HS3L08EPI60H), turn on the emulator according to the procedures described in the H8/300 Series E6000 Emulator User's Manual (HS3008EPI60HE). 2. Verify the user system interface cable connections by accessing ports and checking the bus states of the pins. If an error is detected, recheck the soldered IC socket and the location of pin 1. 3. The emulator connected to this user system interface cable supports tw
Résumé du contenu de la page N° 18
Figure 9 shows the system clock oscillator on the user system interface cable and the subclock input specifications. R1 1 M Ω Vcc 0.8 Vcc 0.8 Vcc HCU04 To E6000 emulator HCU04 0.3 Vcc 0.3 Vcc R2 270Ω 55 ns max. 55 ns max. 0 V OSC1 OSC2 Vcc: User System Vcc (3.0 V to 5.0 V) System clock oscillator Subclock input specifications Figure 9 System Clock Oscillator and Subclock Input Specifications 4. Select the MCU type by setting the MCU type switch (SW1) as follows before using the u
Résumé du contenu de la page N° 19
Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifically designed for the HS3L08EPI60H emulator. Do not use this cable with any other emulator station. 4. To prevent breaking of wires in the ca