Instruction d'utilisation Renesas H8/3854 Series

Résumé du contenu de la page N° 1

H8/3854 Series
Expansion Board
(HS3854EIO60H)
for E6000 Emulator
User’s Manual






HS3854EIO60HE(B)

Résumé du contenu de la page N° 2

Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice.

Résumé du contenu de la page N° 3

Preface Thank you for purchasing this H8/3854 series expansion board (HS3854EIO60H; hereinafter referred to as the expansion board) for the H8/300L series E6000 emulator. The expansion board enables user systems for Renesas's original microcomputer H8/3854 series to be developed using an H8/300L series E6000 emulator (HS3L08EPI60H; hereinafter referred to as the emulator) and the H8/3834 evaluation chip set (HS3834EVI60H). i

Résumé du contenu de la page N° 4

Contents Section 1 Components......................................................................................1 Section 2 Connection Procedures......................................................................2 2.1 Using Emulator without Connecting User System ...........................................................2 2.2 Using Emulator with Connecting User System through User System Interface Cable ....2 Section 3 Reset Switch ...........................................

Résumé du contenu de la page N° 5

Section 1 Components Figure 1 shows the HS3854EIO60H expansion board appearance, and table 1 lists the components of the expansion board. Please make sure you have all of these components when unpacking. Figure 1 HS3854EIO60H Expansion Board Table 1 HS3854EIO60H Components No. Component Quantity Remarks 1 HS3854EIO60H 1 Expansion board 2 Documentation 1 User’s manual for HS3854EIO60H (this manual) 1

Résumé du contenu de la page N° 6

Section 2 Connection Procedures WARNING Always switch OFF the user system and the emulator product before the EXPANSION BOARD or USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on each side is correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system, the emulator product, the user system interface cable, and the expansion board, or will result in PERSONAL INJURY.

Résumé du contenu de la page N° 7

E6000 EMULATOR 2. [1] After making sure the direction of the expansion board connector labeled E6000 EMULATOR is correct, firmly insert the expansion board connector into the emulator station connector ([1] in figure 2). [2] Connect the expansion board labeled USER INTERFACE CABLE and the user system interface cable body. Emulator station [1] Expansion board Cable body connector [2] Reset switch User system interface cable Figure 2 Connecting Expansion Board to Emulator Station an

Résumé du contenu de la page N° 8

Section 3 Reset Switch The reset switch is on the side of the expansion board as shown in figure 2. Pressing the reset switch resets the H8/3854 dot-matrix LCD controller (table 2). Table 2 Reset Types for the Emulator H8/3854 CPU and I/O H8/3854 Dot-Matrix other than LCD Reset Type Condition LCD Controller Controller HDI reset commands Reset CPU — R Go Reset Reset input from the User reset is masked R — user system during user by configuration setting program execution User r

Résumé du contenu de la page N° 9

Section 4 Notice WARNING 1. This expansion board is specifically designed for the HS3L08EPI60H emulator and the HS3834EVI60H evaluation chip set. Do not use this expansion board with any other emulator station. 2. Use the H8/3854 series user system interface cable (HS3854ECH61H for FP-100B or HS3854ECN61H for TFP- 100G). Do not use any other series of user system interface cable. 1. Do not place heavy objects on the expansion board. 2. Power is supplied from

Résumé du contenu de la page N° 10

E6000 EMULATOR 3. To open the case of the expansion board, remove the four screws on the top panel. To close the case, place the top panel on the expansion board, and fix it with the four screws. Screws Upper panel Figure 3 Removing Expansion Board Upper Panel WARNING When using a polarized capacitor, make sure that the polarity is correct when installing the capacitor. Failure to do so will result in a FIRE HAZARD and will damage the user system, the emulator product, the user