Résumé du contenu de la page N° 1
8VM533M-RZ /
8VM533M-RZ-C
® ®
Intel Pentium 4 Processor Motherboard
User's Manual
Rev. 1003
12ME-VM533MRZ-1003
Copyright
© 2004 GIGABYTE TECHNOLOGY CO., LTD
Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from
without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the property of their respective owners.
Notice
Please do not remove any labels on motherboard, this may void the warranty of t
Résumé du contenu de la page N° 2
Mother Board 8VM533M-RZ Motherboard 8VM533M-RZ Feb. 20 ,2004 Feb. 20, 2004
Résumé du contenu de la page N° 3
Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside. 2. Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case. 3. Ho
Résumé du contenu de la page N° 4
Table of Contents Chapter 1 Introduction ................................................................................................5 Features Summary ...........................................................................................................................5 8VM533M-RZ Series Motherboard Layout......................................................................................6 Block Diagram ................................................................................
Résumé du contenu de la page N° 5
English Chapter 1 Introduction Features Summary ® ® CPU Socket 478 for Intel Pentium 4 (Northwood) with HT Technology ® ® Intel Pentium 4 533/400MHz FSB 2nd cache depends on CPU Chipset North Bridge: VIA P4M266A/P4M533 South Bridge: VIA VT8235/VT8237R Memory 2 184-pin DDR DIMM sockets, supports up to 2GB DRAM (Max) Supports DDR266/DDR200 DIMM Supports only 2.5V DDR SDRAM Slots 1 AGP slot 4X (1.5V) device support 3 PCI slots support 33M Hz & PCI 2.2 compliant On-Board IDE 2
Résumé du contenu de la page N° 6
8VM533M-RZ Series Motherboard Layout 20.8 cm # KB_MS FDD ATX SOC KET 478 IDE1 A TX_12V R_USB IDE2 AUDIO V T6103 * VIA P4M 266A/P4M 533 F_AU DIO BAT AGP PCI1 CODEC VIA V T82 35/ PCI2 V T8237R BIOS PCI3 ITE 8705 F_PANEL F_U SB1 COMB CD_IN PWR_LE D "*" For 8VM533M-RZ only. "#" For 8VM533M-RZ-C only. 8VM533M-RZ Series Motherboard - 6 - English VGA USB COMA LPT LAN * CPU_FAN 8VM533M-RZ DDR1 DDR2 24.5 cm
Résumé du contenu de la page N° 7
English Block Diagram Pentium 4 CPUCLK+/- (100/133MHz) Socket 478 CPU AGP 4X System Bus VGA Port 200/266MHz 533/400MHz DDR VIA MCHCLK (100/133MHz) P4M266A/P4M533 AGPCLK AGPCLK66 MHz 66MHz 33 MHz 3 PCI 14.318 MHz VT6103 * 48 MHz BIOS MII PCI BUS 33MHz VIA LPC BUS VT8235/VT8237R Floppy IT8705 LPT Port PS/2 KB/Mouse 24 MHz 33 MHz ATA33/66/ COM A/COMB 6 USB 6 Channel 100/133 Ports CODEC IDE Channels PCICLK (33MHz) PCICLK (33MHz) MCHCLK (100/133MHz) CLK USBCLK (48MHz) CPUCLK+/- (100/133MHz) 14.318 MH
Résumé du contenu de la page N° 8
Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install mem ory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 4 Step 2 Step 1 Step 4 Step 4 Step 3 Step 1: Install the Central Processing Unit (CPU) Before installing the processor, adhere to the following warning: 1. Please m ake sure the CPU type is supported by the m otherboard. 2.
Résumé du contenu de la page N° 9
English Step 1-1: CPU Installation Figure 1. Socket Pull the rod to the 90-degree directly. Actuation Lever Figure 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then m ove the socket lever to the locked position while holding pressure on the center of the CPU. Step 1-2: CPU Cooling Fan Installation Figure 1. Apply the therm al tape(or grease) to provide better heat conduction between
Résumé du contenu de la page N° 10
Step 2: Install Memory Modules Before installing the m emory modules, adhere to the following warning: 1. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause im proper installation. Please change the insert orientation. The motherboard has 2 dual inline memory m odule (DIM M) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the DIMM socket. The DIM M module c
Résumé du contenu de la page N° 11
English Step 3: Install AGP Card 1. Read the relateAGP card's instruction document before install the AGP card into the computer. 2. If your AGP card has "AGP 4X(1.5V) notch" (show below), please make sure your AGP card is AGP 4X(1.5V). 3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firm ly down on the slot .M ake sure your AGP card is locked by the
Résumé du contenu de la page N° 12
z LAN port * LAN is fast Ethernet with 10/100M bps speed. | Line In jack Devices like CD-ROM , walkm an etc. can be connect to Line In jack. } Line Out jack Connect the stereo speakers or earphone to this connector. ~ MIC In jack Microphone can be connect to MIC In jack. After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to "Line In" jack and connect "Center/Subw
Résumé du contenu de la page N° 13
English 1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. Pin No. Definition 4 2 1 GND 2 GND 3 +12V 3 1 4 +12V 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard. Pin No. Definition Pin No. Definition 1 11 1 3.3V 11 3.3V 2 3.3V 12 -12V 3 GND 13 GND 4 VCC 14 PS_O
Résumé du contenu de la page N° 14
4) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and 2.88M bytes floppy disk types. The red stripe of the ribbon cable must be the sam e side with the Pin1. 34 33 2 1 5) IDE1 / IDE2 (IDE1 / IDE2 Connector) Im portant Notice: Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red stripe of the ribbon cable must be the sam e side with the Pin1. 39 40 IDE2 IDE1 2 1 6) BAT (BATTERY) + CAUTION Danger of explosion i
Résumé du contenu de la page N° 15
English 7) F_PANEL (2 x 10 pins Connector) Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront panel to the F_PANEL connector according to the pin assignment below. Soft Po we r Con nector Sp eaker Co nne ctor Messa ge L ED / Po we r / Slee p LED IDE Ha rd Di sk Acti ve LED Reset Swi tch HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPK (Speaker Connector) Pin 1: VCC(+) Pin 2- Pin 3: NC Pin 4: Data(-) RES (Reset Switch) Open:
Résumé du contenu de la page N° 16
9) F_AUDIO (Front Audio Connector) In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigm ent on the cable is the same as the pin assigm ent on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. Please note, you can have the alternative of using front audio connector or of using rear audio connector to play sound. Pin No. Definition 1 MIC 2 GND 3 REF 10 4 Power
Résumé du contenu de la page N° 17
English 12) COMB (COM B Connector) Be careful with the polarity of the COMB connector. Check the pin assignm ent while you connect the COMB cable. Please contact your nearest dealer for optional COMB cable. Pin No. Definition 1 NDCDB- 2 NSINB 3 NSOUTB 2 10 4 NDTRB- 5 GND 1 9 6 NDSRB- 7 NRTSB- 8 NCTSB- 9 NRIB- 10 No Pin - 17 - Hardware Installation Process
Résumé du contenu de la page N° 18
8VM533M-RZ Series Motherboard - 18 - English
Résumé du contenu de la page N° 19
English Chapter 2 BIOS Setup BIOS Setup is an ov erv iew of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This ty pe of information is stored in battery -backed CM OS RAM so that it retains the Setup information w hen the pow er is turned off. ENTERING SETUP Pow ering ON the computer and pressing immediately w ill allow y ou to enter Setup. If y ou require m ore adv anced BIOS s ettings, pleas e go to "Adv anc ed BIOS" s etting m enu. To e
Résumé du contenu de la page N° 20
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden. • Standard CMOS Features This setup page includes all the items in standard c ompatible BIOS. • Advanced BIOS Features This setup page includes all the items of Aw ard special enhanced features. • Integr ated Peripherals This setup page includes all onboard peripherals. • Power Management Setup This setup page includes all the items of Green function features. • PnP/PCI Configur ation This setup
