Instruction d'utilisation GE Monogram ZDB24 BB

Résumé du contenu de la page N° 1

®
GE Monogram
Installation
Instructions
Beverage Center
Model
ZDB24 WW
ZDB24 BB
Wine Chiller
Model
ZDW24 WW
ZDW24 BB
www.monogram.com

Résumé du contenu de la page N° 2

Important Information Beverage Center & Wine Chiller Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Owner’s Manual for future refer- ence. This appliance must be properly grounded. See “Electrical Supply”, page 4. CAUTION WARNING Cet app

Résumé du contenu de la page N° 3

Design Information Beverage Center & Wine Chiller ZDB24 WW The Monogram beverage center or the wine Models White Beverage Center chiller adds an eloquent statement of style, Available convenience and flexibility. ZDB24 BB Black Beverage Center The Monogram beverage center and wine ZDW24 WW chiller can be used freestanding or as a White Wine Chiller built-in. ZDW24 BB Black Wine Chiller Front ventilation allows the beverage center Dimensions or wine chillder to be installed as a built-in Locate

Résumé du contenu de la page N° 4

Installation Preparation Beverage Center & Wine Chiller IMPORTANT - (Please read carefully) Have the wall outlet and circuit checked by a Grounding qualified electrician to make sure the outlet is the FOR PERSONAL SAFETY, THIS APPLIANCE properly grounded. MUST BE PROPERLY GROUNDED. Beverage Center Where a standard 2-prong wall outlet is encoun- or Wine Chiller The power cord of this appliance is equipped tered, it is your personal responsibility and with a three-prong (grounding) plug which obli

Résumé du contenu de la page N° 5

Upper Left Top of Glass Door Corner of Top of Name Plate Glass DOOR NAME PLATE LOCATION Door Frame Side P/N 41005263 Installation Preparation Beverage Center & Wine Chiller To remove the door: Reverse • Remove the top hinge pin using a 1/8" Allen Door Slip Shim wrench. Set aside. Behind Hinge • Lift the door off the bottom hinge. Swing • Remove the top hinge and set aside. Top Hinge • Remove the bottom hinge, the plastic washer and the bottom hinge pin using a Phillips screwdriver. • Install the

Résumé du contenu de la page N° 6

Installation Beverage Center & Wine Chiller Remove all packing material and tape. B. C. Step Tools and materials required: 1 • #2 Phillips screwdriver Remove the Parts List: D. Packaging A. Stainless tubular handle B. 2 Handle standoffs C. 3 Screws for mounting handle standoffs F. E. (2 required, 1 extra) D. 3 Set screws (2 required, 1 extra) E. 3/32" Allen wrench for set screws F. 4 U-Clips G. H. G. 4 Leveling legs H. GE Monogram nameplate A. I. 8 Plug buttons J. Hinge Shims I. K. 2 Screws for

Résumé du contenu de la page N° 7

Installation Beverage Center & Wine Chiller • Tilt the unit slightly to one side to access the A. bottom corner holes. Step • Install a U-Clip into the front and rear holes 3 on the bottom as shown. CAUTION: See illustration. Be sure the tangs Install on the clips are on the outside and the Leveling straight portion is inserted into the holes. • Screw the leveling legs into the U-clips all Legs B. the way until snug. Then, adjust the leveling legs to installation height. • Follow the same proced

Résumé du contenu de la page N° 8

Upper Left Top of Glass Door Top of Name Plate Corner of Glass DOOR NAME PLATE LOCATION Door Frame Side P/N 41005263 Template Beverage Center & Wine Chiller Template For Nameplate Location To be used when door swing has been reversed, with handle on right side, hinge on left side. To position new nameplate: • Remove the original nameplate, now located on the bottom of the door. • Cut template along dotted line. • Hold or tape template behind glass door in the upper left corner so that it is visi