Résumé du contenu de la page N° 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-R2612
CD-RW/DVD-ROM COMBINATION MOBILE DRIVE
USER MANUAL
Résumé du contenu de la page N° 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the CD-RW/DVD-ROM Combo Drive............................4 Troubleshooting.......................................................................7 Specifications ..........................................................................8 Drive Connectors..................................
Résumé du contenu de la page N° 3
INTRODUCTION – SD-R2612 General Features CD-RW disc write/rewrite at 4X – 24X CD-R disc write at 4X - 24X 3-way Disc Eject (eject button, software, emergency eject hole) Average Access Time CD 130ms DVD-ROM (single) 130ms DVD-ROM (dual) 150ms DVD-RAM 250ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM and DVD-ROM discs Regionalization (RPC2 compliance) (DVD) BUS Interface ATAPI Format Compatibility CD: • CD-DA (Red Book) - Standard A
Résumé du contenu de la page N° 4
Front Panel Figure 1.SD-R2612 CD-RW/DVD Combo Drive Front Panel Loading Load disc using tray. Tray The LED lights green or amber when the drive is operating (LED is amber when drive is Busy Indicator writing.) Eject The Eject button is used to open the disc tray so you can install or remove a disc. Button Emergency The emergency eject hole is to be used only when the Loading Tray will not open when Eject button is pressed. Eject Hole
Résumé du contenu de la page N° 5
SETUP – SD-R2612 Toshiba recommends that only trained professionals install this CD-RW/DVD-ROM Combo drive into your laptop/notebook. Installation Notes • The SD-R2612 CD-RW/DVD-ROM Combo drive has no jumpers that need to be set • Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30° (drive with volume control in up position). • When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive. • When mounting d
Résumé du contenu de la page N° 6
USING THE CD-RW/DVD-ROM Combo Drive – SD-R2612 Drive Operation Inserting Media To insert media perform the following steps: Figure 1.Inserting Disc 1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray. 2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc. 3. Gently close the disc tray. Removing Media To remove media disc from the drive, perform the following steps: 1. Open the loading tray by
Résumé du contenu de la page N° 7
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high- speed technology and do not indicate a problem with the drive. Regional Coding Region Protection Coding (RPC) of DVD Discs: this feature is supported on DVD Players and is used
Résumé du contenu de la page N° 8
Handling Media DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD movie skips or hangs during playback, clean the media. Most DVD video playback issues are media- related and can be remedied by proper handling and care of media. Cleaning Media Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a c
Résumé du contenu de la page N° 9
TROUBLESHOOTING – SD-R2612 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by • Is the drive connected properly? Are all cables plugged in system properly (e.g. Power Cable, Interface Cable and Audio Cables). • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the CD-RW/DVD-ROM Combo drive recognized? (BIOS / DOS reports "device driver not found
Résumé du contenu de la page N° 10
SPECIFICATIONS –SD-R2612 General Interface: ATAPI Format Compatibility CD: • CD-DA (Red Book) - Standard Audio CD & CD-TEXT • CD-ROM (Yellow Book Mode1 & 2) - Standard Data\ • CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session • CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge) • CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video • Video-CD (White Book) - MPEG1 Video DVD • DVD DVD-ROM (Book 1.02) • DVD-Video (Book 1.1) • DVD-R (Book 1.0, 3.9G) • DVD-R (Book 2
Résumé du contenu de la page N° 11
Performance Transfer Rate DVD (Single) 10,800KB/second max (8X max) DVD (Dual) 8,100KB/second max (6X max) DVD+/-R 8,100KB/second max (6X max) DVD+/-RW 8,100KB/second max (6X max) DVD-RAM (Ver 2.1) 5,400KB/second max (4X max) CD-ROM/R (Read, Mode 1) 3,600KB/second (24X max) CD-RW Read (Mode 1) 3,600KB/second (24X max) Random Access Time CD-ROM 130ms CD-RW 130ms DVD (single) 130ms DVD (dual) 150ms DVD-R/+R 150ms DVD-RW/+RW 150ms DVD-RAM 250ms Data Error Rate -15 1
Résumé du contenu de la page N° 12
Environmental Ambient Temperature Operating 5° to 50° C (41° to 122° F) Storage -40° to 65° C (-40° to 149° F) Relative Humidity Operating 10% to 90% Storage/Shipping 5% to 95% (wet bulb 40° C max) Vibration 2 Operating (5 to 500 Hz) (read) 2.45 m/s (0.25G) (O-P) 2 Operating (5 to 500Hz) (write) 2.45 m/s (0.25G) (O-P) 2 Non-operating (10 to 500Hz) 9.8 m/s (1.0G) (O-P) 2 Packing (10 to 25 Hz) 9.8 m/s (1.0G) (O-P) 2 Shock (Non-operating) 490 m/s [50G] Acoustical Noi
Résumé du contenu de la page N° 13
Drive Connectors –SD-R2612 Figure 1.SD-R2612 DVD Writeable Drive Rear Panel – Connector ATAPI A 50-pin ATAPI interface connector is found at the rear of the SD-R2612 CD-RW/DVD- ROM Combo drive. Connecting cable should use Japan Aviation Electronics Industry Connector Limited KX14-50Series L or equivalent connector. Table 1.Interface Pin Assignments PIN I/O SIGNAL NAME PIN I/O SIGNAL NAME NO. NO. 1 O Audio L-CH 2 O Audio R-CH 3 Audio Ground 4 Digital Ground 5 I /RESET 6 I
