Résumé du contenu de la page N° 1
Storage Device Division
CD-RW/DVD-ROM
DRIVE
SD-R1102
Installation Instructions
with VOB InstantCD/DVD
and
TM
CyberLink PowerDVD Software
VERSION 1.0
APRIL 2001
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
CD-RW/DVD-ROM DRIVE Instruction Instructions For the following Drive: SD-R1102 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. STORAGE DEVICE DIVISION 35 Hammond Irvine, CA 92618 Contents of this manual are subject to change without prior notice. © 2001 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. All rights reserved Printed in USA P/N 460021-A0
Résumé du contenu de la page N° 4
You have just purchased one of the most advanced storage technologies available. As with any new technology, you must read, and follow all set-up and usage instructions in the applicable user guides and/or manuals en- closed. WARNINGS Operating this optical disk drive (the “Equipment”) outside its rated capacities and speci- fications may cause electrical overload, excessive heat, malfunction, erroneous operation, and/or performance degradation. Please handle the Equipment properly in complian
Résumé du contenu de la page N° 5
6. DO NOT use this Equipment in any system, such as medical equipment, where personal injury or property damages could result from the Equipment’s malfunction, unexpected data corruption, or data error in the reading operation. 7. When a disc cannot be ejected for some reason, you can use the ‘emergency eject’ mechanism. To avoid risk of damages to the disc, turn the power off and wait at least one (1) minute before you eject the disc using the emergency eject mechanism. NOTICE To avoid the ris
Résumé du contenu de la page N° 6
Table of Contents Checking your Kit Packaging ...................................................................... 1 System Requirements .................................................................................... 1 Setting Jumpers ............................................................................................. 2 Placing CD-RW/DVD-ROM inside your computer ...................................... 2 Connecting Cables.............................................................
Résumé du contenu de la page N° 7
Congratulations on your purchase of a Toshiba CD-RW/DVD-ROM drive and Kit. The following information will help you in the simple installation of your new CD-RW/DVD-ROM drive. CHECKING YOUR KIT PACKAGING Please unpack your CD-RW/DVD-ROM kit, and assure that you have the follow- ing items: Toshiba CD-RW/DVD-ROM Drive CD-R Blank Media CD CD-RW Blank Media CD ™ CyberLink PowerDVD Software VOB InstantCD/DVD Software CD CD-RW/DVD-ROM Installation Instructions (this manual) Quick Start
Résumé du contenu de la page N° 8
The following steps must be performed to properly install your CD-RW/DVD- ROM. Set drive’s jumpers Connect audio cable Attach IDE BUS cable Connect power cable Mount CD-RW/DVD-ROM ™ Install CyberLink PowerDVD software (used for viewing DVD movies) Install VOB InstantCD/DVD software (used for recording CDs) SETTING JUMPERS The mode select jumpers are six (6) straight angle pins located on the rear of the CD-RW/DVD-ROM. By placing a jumper on the pins, you can select the following fu
Résumé du contenu de la page N° 9
1. Remove computer cover and faceplate if required (refer to your computer system’s manual for removal information). 2. If the CD-RW/DVD-ROM is replacing a CD-ROM, disconnect all connectors and remove the CD-ROM presently installed in your system. 3. Your Toshiba CD-RW/DVD-ROM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) 4. Carefully start sliding the CD-RW/DVD-ROM into the opening with the disc tray facing the fr
Résumé du contenu de la page N° 10
Connect secondary IDE BUS cable to CD-RW/DVD-ROM drive, assuring that pin 1 of the cable (side with red stripe) is connected to pin 1 on the drive. • If the CD-RW/DVD-ROM is the only drive connected on the secondary IDE BUS cable: connect drive to the last set of pins on IDE BUS cable. If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS cable: connect CD-RW/DVD-ROM to the open middle connector . The CD- RW/DVD-ROM drive should then be jumpered to SL (slave) position. If the
Résumé du contenu de la page N° 11
COMPLETING INSTALLATION After you have connected all the necessary cables, push the CD-RW/DVD-ROM completely into the computer’s drive slot. Mount the drive per your computer’s instructions using the screws included in your kit. If you are using other screws, assure that the screw length does not exceed 3±0.5mm (measured from outside surface of side or bottom of CD-RW/DVD-ROM to tip of screw). Replace the computer cover and all outer screws. ATAPI CD/DVD Software Driver: Toshiba’s CD-RW/DVD-ROM
Résumé du contenu de la page N° 12
™ CyberLink PowerDVD : ™ CyberLink PowerDVD is a high-quality, pure-software DVD player that brings high-quality movies and karaoke into your multimedia PC. You can playback high resolution DVD titles or MPEG-2 files with superb MPEG-2 video and Dolby AC-3 audio quality. ™ To install, insert CyberLink PowerDVD into your newly installed CD-RW/DVD- ROM. Go to Windows Start menu, select “Run” and type d:\setup.exe (substi- tute the appropriate letter of your CD-RW/DVD-ROM drive for d:). Follow the
Résumé du contenu de la page N° 13
SD-R1102 SPECIFICATIONS DVD: 2,048 DATA CAPACITY CD: 2,048 (mode 1) (bytes/block) 2,336 (mode 2) DVD: 5,053rpm (3.3-8X) ROTATIONAL SPEED DVD-R:1,100-2,800rpm (2X) CD: 6,849rpm (13.8-32X) CD-RW:4,281rpm (8.6-20X) CD-R,CD-RW: 1,700- 3,960rpm (8X) SUSTAINED DATA DVD: 4,476 - 10,816KB/sec TRANSFER RATE CD: 2,070 - 4,800KB/sec (mode 1) 2,359 - 5,472KB/sec (mode 2) ACCESS TIME (Typ.) DVD CD Avg. Random Access 130ms 100ms Avg Random Seek 120ms 95ms Avg. Full Stroke 200ms 160ms DATA BUFFER 2Mbytes POWER
Résumé du contenu de la page N° 14
WARRANTY INFORMATION Toshiba America Electronic Components, Inc. (“TAEC”) warrants that all prod- ucts will, upon delivery by TAEC to the customer in new condition, be free from defects in material and workmanship for a period of twelve (12) months after delivery. TAEC warrants that spare Parts and Accessories will be free from defects in material and workmanship for a period of ninety (90) days. These warranties are effective from the date of shipment by TAEC to the original purchaser and will
Résumé du contenu de la page N° 15
Résumé du contenu de la page N° 16
460018-C0 P/N 460021-A0
