Instruction d'utilisation Metra Electronics 99-8206

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-8206
APPLICATIONS
Toyota Highlander 2001-2007
4-Runner (Excluding Limited) 2003-2008
99-8206
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Highlander Brackets • E) 4-Runner Brackets
B
A
E
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
C
Harness:
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp interface harness 2003-up
A

Résumé du contenu de la page N° 2

99-8206 TABLE OF CONTENTS Dash Disassembly - 2003-2008 Toyota 4 Runner (Excluding Limited) . . . . . . . . . 1 - 2001-2007 Toyota Highlander . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - 4 Runner Bracket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Toyota Highlander Bracket Assembly . . . . . . . . . . . . . . . . . . 3 - DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO DIN Head Unit Provision . . . . . . . . . . . . .

Résumé du contenu de la page N° 3

DASH DISASSEMBLY 99-8206 TOYOTA 4 RUNNER 2003-2008 (EXCLUDING LIMITED) A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. Unsnap and remove trim from around 2 shifter. 3 Unsnap and remove trim covers from around center console pocket edge at front and rear of console. B 4 Unsnap and remove center console cover. (Figure A) 5 Unsnap trim ring from around ignition key cylinder. 6 Remove (1) 10 mm bolt from bottom right of panel below steering column. Unsnap pa

Résumé du contenu de la page N° 4

DASH DISASSEMBLY 99-8206 TOYOTA HIGHLANDER 2001-2007 A Disconnect the negative battery 1 terminal to prevent an accidental short circuit. 2 Pull and remove dash panel from radio and climate controls. Tip: There are 8 clips. (Figure A) 3 Remove (6) 10mm bolts from radio and climate controls assembly. (Figure B) B Remove assembly and disconnect 4 the wiring. Remove (8) Phillips bolts and (4) Phillips 5 screws to separate brackets from assem- bly. (Figure C) C 2

Résumé du contenu de la page N° 5

KIT DISASSEMBLY 99-8206 4 RUNNER BRACKET ASSEMBLY TOYOTA HIGHLANDER BRACKET ASSEMBLY A 1 Snap the appropriately marked Mounting Brackets for your application onto the sides of the Radio Housing. The brackets are marked 4-Runner or Highlander and left or right. (Figure A - 4 RUNNER) (Figure B - HIGHLANDER) B 3

Résumé du contenu de la page N° 6

KIT ASSEMBLY 99-8206 DIN HEAD UNIT PROVISION WITH POCKET A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Snap the aftermarket radio into the cage and secure. (Figure B) B 4

Résumé du contenu de la page N° 7

KIT ASSEMBLY 99-8206 ISO DIN HEAD UNIT PROVISION A 1 Mount the ISO Brackets to the head unit with the screws supplied with the radio. (Figure A) 2 Snap the radio into the radio housing until the side clips engage. (Figure B) Snap the ISO Trim Plate onto the 3 Radio/Housing assembly. (Figure B) B 5

Résumé du contenu de la page N° 8

FINAL ASSEMBLY 99-8206 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassem