Résumé du contenu de la page N° 1
C141-E050-02EN
MHC2032AT, MHC2040AT
MHD2032AT, MHD2021AT
DISK DRIVES
PRODUCT MANUAL
Résumé du contenu de la page N° 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. IMPOR
Résumé du contenu de la page N° 3
Résumé du contenu de la page N° 4
Revision History (1/1) Edition Date Revised section (*1) Details (Added/Deleted/Altered) 01 1998-02-15 — — 02 1998-0- *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C141-E050-02EN
Résumé du contenu de la page N° 5
Résumé du contenu de la page N° 6
Preface This manual describes the MHC Series and MHD Series, 2.5-inch hard disk drives. These drives have a built-in controller that is compatible with the ATA interface. This manual describes the specifications and functions of the drives and explains in detail how to incorporate the drives into user systems. This manual assumes that the reader has a basic knowledge of hard disk drives and their implementations in computer systems. This manual consists of seven chapters and sections explaining
Résumé du contenu de la page N° 7
Preface Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazarous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also indicates that
Résumé du contenu de la page N° 8
Preface Liability Exception “Disk drive defects” refers to defects that involve adjustment, repair, or replacement. Fujitsu is not liable for any other disk drive defects, such as those caused by user misoperation or mishandling, inappropriate operating environments, defects in the power supply or cable, problems of the host system, or other causes outside the disk drive. C141-E050-02EN iii
Résumé du contenu de la page N° 9
Résumé du contenu de la page N° 10
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the predate or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Normal Operation Data corruption: Avoid mounting the disk near strong 3-6 magnetic soures such as loud speakers. Ensure that the
Résumé du contenu de la page N° 11
Résumé du contenu de la page N° 12
Contents CHAPTER 1 Device Overview........................................................................ 1-1 1.1 Features 1-2 1.1.1 Functions and performance 1-2 1.1.2 Adaptability 1-2 1.1.3 Interface 1-3 1.2 Device Specifications 1-4 1.2.1 Specifications summary 1-4 1.2.2 Model and product number 1-6 1.3 Power Requirements 1-6 1.4 Environmental Specifications 1-8 1.5 Acoustic Noise 1-8 1.6 Shock and Vibration 1-9 1.7 Reliability 1-9 1.8 Error Ra
Résumé du contenu de la page N° 13
Contents CHAPTER 3 Installation Conditions..............................................................3-1 3.1 Dimensions 3-2 3.2 Mounting 3-4 3.3 Cable Connections 3-8 3.3.1 Device connector 3-8 3.3.2 Cable connector specifications 3-9 3.3.3 Device connection 3-9 3.3.4 Power supply connector (CN1) 3-10 3.4 Jumper Settings 3-10 3.4.1 Location of setting jumpers 3-10 3.4.2 Factory default setting 3-11 3.4.3 Master drive-slave drive setting 3-11 3.4.4 C
Résumé du contenu de la page N° 14
Contents 4.6.1 Read/write preamplifier (PreAMP) 4-9 4.6.2 Write circuit 4-10 4.6.3 Read circuit 4-12 4.6.4 Digital PLL circuit 4-13 4.7 Servo Control 4-14 4.7.1 Servo control circuit 4-14 4.7.2 Data-surface servo format 4-18 4.7.3 Servo frame format 4-18 4.7.4 Actuator motor control 4-19 4.7.5 Spindle motor control 4-20 CHAPTER 5 Interface ..................................................................................... 5-1 5.1 Physical Interface 5
Résumé du contenu de la page N° 15
Contents 5.5.2 Phases of operation 5-78 5.5.2.1 Ultra DMA burst initiation phase 5-78 5.5.2.2 Data transfer phase 5-79 5.5.2.3 Ultra DMA burst termination phase 5-79 5.5.3 Ultra DMA data in commands 5-80 5.5.3.1 Initiating an Ultra DMA data in burst 5-80 5.5.3.2 The data in transfer 5-81 5.5.3.3 Pausing an Ultra DMA data in burst 5-81 5.5.3.4 Terminating an Ultra DMA data in burst 5-82 5.5.4 Ultra DMA data out commands 5-85 5.5.4.1 Initiating an Ultra DMA
Résumé du contenu de la page N° 16
Contents CHAPTER 6 Operations ................................................................................. 6-1 6.1 Device Response to the Reset 6-2 6.1.1 Response to power-on 6-2 6.1.2 Response to hardware reset 6-4 6.1.3 Response to software reset 6-5 6.1.4 Response to diagnostic command 6-6 6.2 Address Translation 6-7 6.2.1 Default parameters 6-7 6.2.2 Logical address 6-8 6.3 Power Save 6-9 6.3.1 Power save mode 6-9 6.3.2 Power commands 6-11 6.4
Résumé du contenu de la page N° 17
Contents Illustrations Figures Figure 1.1 Current fluctuation (Typ.) at +5V when power is turned on 1-6 Figure 2.1 Disk drives outerview (The MHC Series and MHD Series) 2-2 Figure 2.2 Configuration of disk media heads 2-3 Figure 2.3 1 drive system configuration 2-4 Figure 2.4 2 drives configuration 2-5 Figure 3.1 Dimensions (MHC/MHD series) 3-2 Figure 3.2 Orientation (Sample: MHC2040AT) 3-4 Figure 3.3 Mounting frame structure 3-5 Figure 3.4 Surface temperature mea
Résumé du contenu de la page N° 18
Contents Figure 5.5 WRITE SECTOR(S) command protocol 5-73 Figure 5.6 Protocol for the command execution without data transfer 5- 75 Figure 5.7 Normal DMA data transfer 5-76 Figure 5.8 An example of generation of parallel CRC 5-90 Figure 5.9 Ultra DMA termination with pull-up or pull-down 5-91 Figure 5.10 Data transfer timing 5-93 Figure 5.11 Single word DMA data transfer timing (mode 2) 5-94 Figure 5.12 Multiword DMA data transfer timing (mode 2) 5-95 Figure 5.13
Résumé du contenu de la page N° 19
Contents Table 3.1 Surface temperature measurement points and standard values 3-6 Table 3.2 Cable connector specifications 3-9 Table 4.1 Self-calibration execution timechart 4-9 Table 4.2 Write precompensation algorithm 4-10 Table 5.1 Signal assignment on the interface connector 5-3 Table 5.2 I/O registers 5-7 Table 5.3 Command code and parameters 5-14 Table 5.4 Information to be read by IDENTIFY DEVICE command 5- 32 Table 5.5 Features register values and settable mod
Résumé du contenu de la page N° 20
CHAPTER 1 Device Overview 1.1 Features 1.2 Device Specifications 1.3 Power Requirements 1.4 Environmental Specifications 1.5 Acoustic Noise 1.6 Shock and Vibration 1.7 Reliability 1.8 Error Rate 1.9 Media Defects Overview and features are described in this chapter, and specifications and power requirement are described. The MHC Series and MHD Series are 2.5-inch hard disk drives with built-in disk controllers. These disk drives use the AT-bus hard disk interface protocol and are compact and rel
