Résumé du contenu de la page N° 1
C141-E270-01EN
MBA3300NC, MBA3300NP
MBA3147NC, MBA3147NP
MBA3073NC, MBA3073NP
HARD DISK DRIVES
PRODUCT MANUAL
Résumé du contenu de la page N° 2
FOR SAFE OPERATION Handling of This manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this m
Résumé du contenu de la page N° 3
REVISION RECORD Edition Date published Revised contents 01 October, 2007 Specification No.: C141-E270-**EN C141-E270
Résumé du contenu de la page N° 4
Related Standards Product specifications and functions described in this manual comply with the following ANSI (*1) standards. Document number Title T10/1236D Rev.20 [NCITS.351:2001] SCSI Primary Commands-2 (SPC-2) T10/996D Rev.8c [NCITS.306:1998] SCSI-3 Block Commands (SBC) T10/1157D Rev.24 SCSI Architecture Model-2 (SAM-2) T10/1365D Rev.10 SCSI Parallel Interface-4 (SPI-4) *1 ANSI = American National Standard Institute In case of conflict between this manual and any referenced
Résumé du contenu de la page N° 5
PREFACE This manual describes the MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP, MBA3073NC, and MBA3073NP 3.5-inch SCSI hard disk drives. This manual details the specifications and functions of the above disk drives, and gives the requirements and procedures for installing it into a host computer system. This manual is written for users who have a basic understanding of SCSI disk drives and their use in computer systems. The MANUAL ORGANIZATION section describes organization and scope of thi
Résumé du contenu de la page N° 6
CONVENTIONS USED IN THIS MANUAL The MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP, MBA3073NC, and MBA3073NP disk drives are described as "the hard disk drive (HDD)," "the disk drive" or "the device" in this manual. Decimal number is represented normally. Hexadecimal number is represented as X'17B9', 17B9h or 17B9H. Binary number is represented as "010". CONVENTIONS FOR ALERT MESSAGES This manual uses the following conventions to show the alert messages. An alert message consists of an a
Résumé du contenu de la page N° 7
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also indicates that damages to the product or other property may occur if the user does not perform the procedure correctly. Task Alert message Page Installation Damage Never remove any labels from the HDD or deface them in any way.
Résumé du contenu de la page N° 8
Task Alert message Page Installation High temperature To prevent injury, never touch the HDD while it is hot. The DE and LSI 93 become hot during operation and remain hot immediately after turning off the power. Diagnostics and Data loss Maintenance When the SEND DIAGNOSTIC command terminates with the CHECK 98 CONDITION status, the initiator must collect the error information using the REQUEST SENSE command. The RECEIVE DIAGNOSTIC RESULTS command cannot read out the error info
Résumé du contenu de la page N° 9
MANUAL ORGANIZATION PRODUCT 1. General Description MANUAL 2. Specifications 3. Data Format (This manual) 4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 7. Error Analysis SCSI PHYSICAL 1. SCSI Bus INTERFACE 2. SCSI Message SPECIFICATIONS 3. Error Recovery SCSI LOGICAL 1. Command Processing INTERFACE 2. Data Buffer Management SPECIFICATIONS 3. Command Specifications 4. Parameter Data Formats 5. Sense Data and Error Recovery
Résumé du contenu de la page N° 10
This page is intentionally left blank.
Résumé du contenu de la page N° 11
CONTENTS page CHAPTER 1 GENERAL DESCRIPTION............................................................................ 13 1.1 Standard Features ............................................................................................................. 14 1.2 Hardware Structure .......................................................................................................... 18 1.3 System Configuration..............................................................................
Résumé du contenu de la page N° 12
4.3.2 68-pin connector type 16-bit SCSI model (NP model) .................................................... 60 4.3.3 Cable connector requirements .......................................................................................... 67 4.3.4 External operator panel (on NP model drives only)......................................................... 68 CHAPTER 5 INSTALLATION.............................................................................................. 71 5.1 Notes on Handl
Résumé du contenu de la page N° 13
6.4.1 Outline of troubleshooting procedures............................................................................. 105 6.4.2 Troubleshooting with HDD replacement in the field ....................................................... 105 6.4.3 Troubleshooting at the repair site..................................................................................... 107 6.4.4 Troubleshooting with parts replacement in the factory.................................................... 108 6.4.5 Fin
Résumé du contenu de la page N° 14
FIGURES page Figure 1.1 System configuration...........................................................................................................19 Figure 3.1 Cylinder configuration.........................................................................................................32 Figure 3.2 Spare area in cell..................................................................................................................34 Figure 3.3 Alternate cylinder ......................
Résumé du contenu de la page N° 15
Figure 4.23 External operator panel circuit example ..............................................................................68 Figure 5.1 SCSI bus connections ..........................................................................................................74 Figure 5.2 Setting terminals location (on NP models only)..................................................................75 Figure 5.3 CN2 setting terminal (on NP models only) ...........................................
Résumé du contenu de la page N° 16
TABLES page Table 2.1 Model names and order numbers.........................................................................................21 Table 2.2 Function specifications........................................................................................................22 Table 2.2 Function specifications (continued).....................................................................................23 Table 2.3 Environmental/power requirements.....................................
Résumé du contenu de la page N° 17
CHAPTER 1 GENERAL DESCRIPTION 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration This chapter describes the feature and configuration of the MBA3xxxxx. The HDDs are high performance large capacity 3.5-inch hard disk drives with an embedded SCSI controller. The HDDs support the Small Computer System Interface (SCSI) as described in the ANSI SCSI SPI-4 [T10/1365D Rev.10] to the extent described in this manual. The flexibility and expandability of the SCS
Résumé du contenu de la page N° 18
1.1 Standard Features (1) Compactness Since the SCSI controller circuit is embedded in the standard 3.5-inch hard disk drive form factor, the HDD is extremely compact. The HDD can be connected directly to the SCSI bus of the host system. (2) Environmental Protection The HDDs comply with the Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS) directive issued by European Union (EU). (3) SCSI standard The HDD provides not only SCSI b
Résumé du contenu de la page N° 19
(5) High speed data transfer Such a high data transfer rate on the SCSI bus can be useful with the large capacity buffer in the HDD. • 8-bit SCSI: The data transfer rate on the SCSI bus is 40 MB/s maximum at the synchronous mode. • 16-bit SCSI: The data transfer rate on the SCSI bus is 320 MB/s maximum at the paced transfer synchronous mode. Note: The maximum data transfer rate in asynchronous mode may be limited by the response time of initiator and the length of SCSI bus length
Résumé du contenu de la page N° 20
IMPORTANT When Write cache is enabled, you should ensure that the cached data is surely flushed to the disk media before you turn off the HDD's power. To ensure it, you should issue either the SYNCHRONIZE CACHE command or the STOP UNIT command with specifying “0” to the Immediate bit and then confirm that the command is surely terminated with the GOOD STATUS. (9) Command queuing feature The HDD can queue maximum 128 commands, and optimizes the issuing order of queued commands by the
