Résumé du contenu de la page N° 1
Agilent 82357B
USB/GPIB
Interface
Quick Start Guide
Agilent Technologies
Résumé du contenu de la page N° 2
Notices © Agilent Technologies, Inc. 2006 - 2009 Warranty No part of this manual may be reproduced The material contained in this document in any form or by any means (including is provided “as is,” and is subject to electronic storage and retrieval or transla- being changed, without notice, in future tion into a foreign language) without prior editions. Further, to the maximum extent agreement and written consent from Agi- permitted by applicable law, Agilent dis- lent Technologies, Inc.
Résumé du contenu de la page N° 3
Safety Symbols Caution, risk of danger (refer to this manual for specific Warning or Caution information) Regulatory Markings The CE mark is a registered trademark of the European Commu- nity. This CE mark shows that the product complies with all the relevant European Legal Directives. ICES/NMB-001 indicates that this ISM device complies with the Canadian ICES-001. Cet appareil ISM est confomre a la norme NMB-001 du Canada. The CSA mark is a registered trademark of the Canadian Stan- dards A
Résumé du contenu de la page N° 4
Additional Safety Information The following general safety precautions must be observed during all phases of operation of this instrument. � Use the device with the cables provided. CAU CAUT TIIO ON N � Repair or service that is not covered in this manual should only be performed by qualified personnels. � Do not use the device if it appears damaged or WARNING defective. � Observe all markings on the device before connecting any wiring to the device. � Do no operate the device in the presenc
Résumé du contenu de la page N° 5
82357B USB/GPIB Interface Table of Contents Introduction 1. Before You Install the 82357B Check your shipment items 2 Check your PC operating system 2 2. Installing Agilent IO Libraries Suite Insert the Automation-Ready CD 3 Install the IO Libraries Suite 3 Look for circled IO icon 4 3. Connecting the 82357B Plug the 82357B into a USB Port 5 Observe the 82357B LEDs 5 4. Configuring the 82357B Observe the Agilent Connection Expert 6 Configure the 82357B 6 5. Connecting
Résumé du contenu de la page N° 6
82357B USB/GPIB Interface Introduction Introduction This quick start guide shows a suggested six-step process to install the 82357B and the Agilent IO Libraries Suite, to con- nect the 82357B to your PC, to configure the 82357B, and to program GPIB instruments via the 82357B. It also includes the product technical specifications information. The 82357B USB/GPIB Interface is supported ONLY for PCs NOTE with Windows XP Professional, Windows Vista, or Windows 7 operating systems. The operating
Résumé du contenu de la page N° 7
82357B USB/GPIB Interface 1. Before You Install the 82357B 1. Before You Install the 82357B Check your shipment items Verify that you received the following items in your shipment of the 82357B USB/GPIB Interface: � Agilent 82357B USB/GPIB Interface � Agilent Automation-Ready CD with Agilent IO Libraries Suite � Printed copy of the Agilent 82357B USB/GPIB Interface Quick Start Guide If any item is missing or damaged, keep the shipping materials and contact Agilent Technologies. See “Other Re
Résumé du contenu de la page N° 8
82357B USB/GPIB Interface 2. Installing Agilent IO Libraries Suite 2. Installing Agilent IO Libraries Suite Insert the Automation-Ready CD Turn on your PC and insert the Agilent Automation- Ready CD with Agilent IO Libraries Suite into the CD-ROM drive. If the auto-run window does not appear automatically, go to Start > Run then type :autorun\auto.exe, where is your CD drive letter. Install the IO Libraries Suite � See the 82357B User’s Guide for the full IO Libraries Suite N
Résumé du contenu de la page N° 9
82357B USB/GPIB Interface 2. Installing Agilent IO Libraries Suite Upgrading your IO Libraries version NOTE If you are upgrading to the latest version of the IO Libraries Suite from a previous version of the IO Libraries, you must remove the following instruments and interfaces listed below before you upgrade your software. This step is necessary in order for these devices to obtain the correct drivers to work with Agilent IO Libraries. � Disconnect any USB instruments from your PC. � Disco
Résumé du contenu de la page N° 10
82357B USB/GPIB Interface 3. Connecting the 82357B 3. Connecting the 82357B Plug the 82357B into a USB Port Plug the 82357B USB cable into an available USB port on your PC or on a supported USB hub. To connect to USB hubs, see the 82357B User's Guide. The picture shown below is for illus- tration purposes only. It is not necessary to connect the 82357B to any GPIB instruments at this time. Observe the 82357B LEDs Observe the three LEDs on the 82357B. Initially, only the red FAIL LED should b
Résumé du contenu de la page N° 11
82357B USB/GPIB Interface 4. Configuring the 82357B 4. Configuring the 82357B Observe the Agilent Connection Expert Run the Agilent Connection Expert to verify your I/O configura- tion: In the Windows Notification area, click the IO icon ( ), then click Agilent Connection Expert. When the main screen appears, you will see a map of the sys- tem connections in the Instrument I/O on this PC pane (also called the “Explorer Pane”). At this time, the Connection Expert window should refresh. If it
Résumé du contenu de la page N° 12
82357B USB/GPIB Interface 5. Connecting GPIB Instruments 5. Connecting GPIB Instruments Connect the 82357B to GPIB instruments Connect one or more GPIB instruments (up to 14 instruments maximum) to the GPIB connector on the 82357B as shown below: � Single instrument connection 82357 82357BB GPIB Instrument USB Cable � Multiple instruments connection 82357 82357B B GPIB Instrument USB Cable GPIB Instrument GPIB Cables GPIB Instrument To minimize stress on the connector mountings, stack no more
Résumé du contenu de la page N° 13
82357B USB/GPIB Interface 6. Programming via the 82357B 6. Programming via the 82357B Use the Agilent Interactive IO to communicate with the GPIB instruments After the 82357B has been configured and connected to the GPIB instruments, you can use the Interactive IO to establish communication between your PC and the connected GPIB instruments. To run the Interactive IO for an IEEE-488.2 compli- ant instrument, perform the following: 1 Right click the instrument's icon in the Connection Expert
Résumé du contenu de la page N° 14
82357B USB/GPIB Interface Other References Other References Related documentation See the following documents for information related to the 82357B. All documents are available in electronic format by clicking on the IO icon ( ) on the Windows task bar then selecting Documentation. � Agilent 82357B USB/GPIB Interface User's Guide describes the 82357B, and provides installation and troubleshooting information. � Agilent IO Libraries Connectivity Guide provides a descrip- tion of the Agilent
Résumé du contenu de la page N° 15
82357B USB/GPIB Interface Other References 10 82357B Quick Start Guide
Résumé du contenu de la page N° 16
www.agilent.com Contact us To obtain service, warranty or technical assistance, contact us at the following phone or fax numbers: United States: (tel) 800 829 4444 (fax) 800 829 4433 Canada: (tel) 877 894 4414 (fax) 800 746 4866 China: (tel) 800 810 0189 (fax) 800 820 2816 Europe: (tel) 31 20 547 2111 Japan: (tel) (81) 426 56 7832 (fax) (81) 426 56 7840 Korea: (tel) (080) 769 0800 (fax) (080) 769 0900 Latin America: (tel) (305) 269 7500 Taiwan: (tel) 0800 047 866 (fax) 0800 286 331 Other Asia
