Résumé du contenu de la page N° 1
Safety Instructions & Operator’s Manual for
SINGLE STAGE
SNOW THROWER
SERIES 0
Model Mfg. No.
3190M 1694382
3190E 1694383
MODEL NUMBER EXPLANATION
3 19 0 E
ENGINE HP ENGINE OPTIONS
AUGER WIDTH SERIES DESIGNATION
3 – 3.0 HP (Engine Horse Power) 19 – 19” Auger Width 0 -- Series Designation
E – 110 Volt Electric Start
M – Manual, Recoil Start
Before operating your Snow Thrower, read this manual carefully and pay particular at
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermore, must allow only persons who understand these instructions to operate snow thrower. Each person operating the snow thrower must be of sound m
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS 5. DO NOT store the machine or fuel container inside OPERATIONAL PRECAUTIONS where there is an open flame, spark or pilot light 8. Start engine only where exhaust fumes will be safely such as on a water heater or other appliances. dissipated. Allow a brief warm-up period, and 6. DO NOT fill fuel containers inside a vehicle or on a practice operation of controls outside before putting truck or trailer bed with a plastic liner. Always place the machine to
Résumé du contenu de la page N° 4
TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS.......................... 2-3 TABLE OF CONTENTS ............................................................................ 4 SECTION 2 - OPERATING INSTRUCTIONS......................................... 5-9 Pre-start Checklist ...........................................................................................5-6 Starting & Stopping Engine (Recoil Start Models) ........................................ 7-8 Start
Résumé du contenu de la page N° 5
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service STANDARD FLUID MEASUREMENT (32:1 Ratio) required before each start-up. 2.1.1. Check guards, chutes, deflectors and covers to GASOLINE 2 CYCLE OIL make sure all are in place and securely tightened. (Gallons) (Ounces) 2.1.2. Check auger control to insure it works freely. 0.25 1.00 See Figure 2.1. 0.50 2.00 0.75 3.00 AUGER 1.00 4.00 CONTROL 1.25 5.00 1.50 6.00 2.0
Résumé du contenu de la page N° 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST (Continued from Previous Page) Make the following checks and perform the service required before each start-up. WARNING DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediat
Résumé du contenu de la page N° 7
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, STOPPING & OPERATION WARNING (RECOIL START MODELS) 2.2.1. ENGINE & AUGER Release auger clutch control and make sure auger/impeller has STOPPED before rotating discharge 1. Move choke control to the choke “ON” position. chute or adjusting deflector. DO NOT place hands near See Figure 2.4. auger/impeller while engine is running. NOTE: Stop the auger by releasing the auger control. Stop the engine by turning the key switch to th
Résumé du contenu de la page N° 8
Section 2 - OPERATING INSTRUCTIONS 2.2.4. STOPPING 1. Connect the power cord to the starter switch box Stop the auger by releasing the auger control. Stop on machine’s control panel then plug the other end into 120 volt AC receptacle. the engine by turning the key switch to the “OFF” 2. Turn ignition key to the “ON” position. position. Always remove key from key switch 3. Move choke control to the choke “ON” position. before leaving machine unattended. See See Figure 2.8. Fi
Résumé du contenu de la page N° 9
Section 2 - OPERATING INSTRUCTIONS WARNING Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.6. ENGAGING AUGER 1. Pull auger control against handle to engage auger. See Figure 2.5. WARNING Release auger clutch control and make sure auger/impeller has STOPPE
Résumé du contenu de la page N° 10
Section 3 - MAINTENANCE 3.1 INTRODUCTION 3.2.3 CHECK AUGER CLUTCH CONTROL CABLE To retain the quality of the snow thrower, use only 1. Visually check cable for fraying, kinking or severed factory authorized replacement parts. Contact a cable strands. Replace cable and adjust tension before local authorized dealer for parts and service operating snow thrower. See Figure 3.3. assistance. For the correct part or other information for a particular snow thrower, always mention the Mod
Résumé du contenu de la page N° 11
Section 4 - REPAIR & ADJUSTMENTS 4.1.2. AUGER BELT IDLER PULLEY WARNING ADJUSTMENT DO NOT attempt any adjustments, maintenance, NOTE: To adjust the idler pulley and properly tension service, or repairs with engine running. Stop auger. the auger belt, the auger control cable adjustment Stop engine. Remove key. Remove spark plug wire must first be loosened as described in the following step. Cable adjustment must be checked after and secure wire away from spark plug. completing the
Résumé du contenu de la page N° 12
Section 4 - REPAIR & ADJUSTMENTS 4. Push the spring tensioned idler pulley down and WARNING install new belt. See Figure 4.5. DO NOT attempt any adjustments, maintenance, service, or repairs with engine running. Stop auger. BELT COVER Stop engine. Remove key. Remove spark plug wire RETAINING STUDS SHOWN REMOVED and secure wire away from spark plug. 4.1.2. AUGER BELT IDLER PULLEY ADJUSTMENT (Continued From Previous Page) 3. Loosen nut and bolt that secures the idler pull
Résumé du contenu de la page N° 13
Section 4 - REPAIR & ADJUSTMENTS WARNING AUGER DO NOT attempt any adjustments, maintenance, FLITE SHOE service, or repairs with engine running. Stop auger. Stop engine. Remove key. Remove spark plug wire and secure wire away from spark plug. 4.1.3. AUGER BELT REPLACEMENT (Continued From Previous Page) 5. Reinstall belt guide. IMPORTANT: Make sure when reinstalling belt guide that it does not touch drive pulley. Belt guide should an equal amount of clearance on both belt g
Résumé du contenu de la page N° 14
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel/oil mix. Using Recoil Starter 2. Engine needs choking & priming. 2. Move choke control to “CHOKE” position. Push primer bulb three times. 3. Spark plug fouled or wire disconnected. 3. Replace spark plug. Attach plug wire onto spark plug. Engine Will Not Crank 1. Power extension cord not plugged into machine or 1. Plug power extension cord into mach
Résumé du contenu de la page N° 15
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. For ninety (90) days from purchase date for the original purchaser's commercial, rental, or other non-residential u
Résumé du contenu de la page N° 16
Safety Instructions & Operator’s Manual for SINGLE STAGE SNOW THROWER SERIES 0 IMPORTANT These products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any
