Résumé du contenu de la page N° 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY PLATINUM
Safety Notice
MP-2105 HOME GYM
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-2105
Retain This
Manual for
Reference
10-26-06
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.
Résumé du contenu de la page N° 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 7 WEIGHT RESISTANCE CHART..................................................
Résumé du contenu de la page N° 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a
Résumé du contenu de la page N° 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Résumé du contenu de la page N° 5
HARDWARE PACK 4
Résumé du contenu de la page N° 6
HARDWARE PACK 5
Résumé du contenu de la page N° 7
HARDWARE PACK 6
Résumé du contenu de la page N° 8
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#78) and Ø ¾” Washer (#92) from bottom. Attach two Rubber Bumpers (#55) onto top of the two Guide Rods and slide down
Résumé du contenu de la page N° 9
DIAGRAM 1 8
Résumé du contenu de la page N° 10
STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and ∅ ¾” Washers (#92). DO NOT tighten the Bolts yet. B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2 ¾” Bracket (#25), two ∅ ¾” Washers (#92), and two M10 Aircraft Nuts (#91). C.) Securely tighten all Nuts and Bolts previously installed. D.) Attach the Seat Support Frame (#7) t
Résumé du contenu de la page N° 11
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2). Secure it with one 7 ½” Front Press Axle (#30), two Ø1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). C.) Thread the T-shaped Lock Pin (#39) into the hole on the Front Press to obtain the desired Front Press position. D.
Résumé du contenu de la page N° 12
DIAGRAM 3 11
Résumé du contenu de la page N° 13
STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height. C.) Insert the Foam Tube (#23) halfway through the hole on the Leg Developer (#8). Push two Foam Rolls (#48) onto the Foam Tube from both ends. Plug two Foam Rol
Résumé du contenu de la page N° 14
STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and ∅ 1 ¼” Washer (#59) from the bottom. C.) Repeat Procedures A and B above to install the other side. Do not over tighten the Bolts. Make sure the Handles are able to swivel. DIAGRAM 5 13
Résumé du contenu de la page N° 15
CABLE LOOP DIAGRAM 14
Résumé du contenu de la page N° 16
STEP 6 (See Diagram 6 & Upper Cable Loop Diagram) A.) Attach the 163” Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 ½” Allen Bolt (#77), two Pulley Bushings (#49), and one M10 Aircraft Nut (#91). C.) Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the opening in the middle of Upper
Résumé du contenu de la page N° 17
DIAGRAM 6 16
Résumé du contenu de la page N° 18
Upper Cable Loop Diagram 17
Résumé du contenu de la page N° 19
STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 164” Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two ∅ 7/8” Leg Developer Pulley Bushings (#52), and one M10 Aircraft Nut (#91). B.) Draw the Cable underneath the Pulley to the open bracket on the Front Base Frame (#12). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#83), two ∅ ¾” Washers
Résumé du contenu de la page N° 20
DIAGRAM 7 19
