Résumé du contenu de la page N° 1
NOTE:
Please read all
instructions carefully
before using this product
MARCY CLASSIC
Table of Contents
Safety Notice
WEIGHT BENCH
Hardware Pack
MCB-849
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MCB-849
Retain This
Manual for
Reference
®
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
09/25/08
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
OWNER'S info@impex-
Résumé du contenu de la page N° 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK………............................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 6 EXPLODED DIAGRAM......................................................
Résumé du contenu de la page N° 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should u
Résumé du contenu de la page N° 4
WARNING LABEL REPLACEMENT The Warning Labels shown here have been placed on the Rear Base Frame and Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-999- 8899 for replacement. Apply the labels in location shown 3
Résumé du contenu de la page N° 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
Résumé du contenu de la page N° 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
Résumé du contenu de la page N° 7
ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended for two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach one Base Frame (#3) to the Rear Base Frame (#2). Attach an Upright Beam (#1) onto the Base Frame and Rear Base Frame. Secure them together with two M10 x 3 5/8” Carriage Bolts (#32), one 5 ½” x 2” Bracket (#15), two Ø ¾” Washer (#41), and
Résumé du contenu de la page N° 8
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#5) to the Rear Stabilizer (#6). Secure it with two M10 x 2 ¾” Carriage Bolts (#33), one 5 1/8” x 2 ¾” Bracket (#14), two Ø ¾” Washers (#41), and two M10 Aircraft Nuts (#44). B.) Attach the two Incline Support Frames (#12) to the Main Seat Support. Secure them to the Main Seat Support with three M10 x 3 5/8” Allen Bolts (#35), six Ø ¾” Washers (#41), and three M10 Aircraft Nuts (#44). DIAGRAM 2 7
Résumé du contenu de la page N° 9
STEP 3 (See Diagram 3) A.) Attach the pivot on the Leg Developer Holder (#7) to the open bracket on the Main Seat Support (#5). Attach the bottom of Leg Developer Holder to the Main Seat Support. Secure it with one M10 x 2 ¾” Carriage Bolt (#33) from front, one M10 x 2 ½” Allen Bolt (#37) from rear, two Ø ¾” Washers (#41), and one M10 Aircraft Nut (#44). B.) Attach the Incline Support (#9) to the side-holes on the two Backrest Supports (#8). Align the holes. Secure it with one M10 x 5 ½” A
Résumé du contenu de la page N° 10
STEP 4 (See Diagram 4) A.) Attach the Backrest Board (#17) to the Backrest Supports (#8). Secure it with four M8 x 1 5/8” Allen Bolts (#38) and four Ø 5/8” Washers (#42). B.) Place the Seat Pad (#16) onto the seat bracket on Leg Developer Holder (#7). Secure it with one M8 x 1 5/8” Allen Bolts (#38), two M8 x 5/8” Allen Bolts (#39), and three Ø 5/8” Washers (#42). DIAGRAM 4 9
Résumé du contenu de la page N° 11
STEP 5 (See Diagram 5) A.) Attach two Ø 5/8” Bushings (#20) to the Leg Developer (#10). Attach the Leg Developer to the Leg Developer Holder (#7). Secure it with one M10 x 3 1/8” Allen Bolt (#36), two Ø ¾” Washers (#41), and one M10 Aircraft Nut (#44). B.) Insert three Foam Tubes (#13) halfway through the holes on the Leg Developer and Leg Developer Holder. Push six Foam Rolls (#27) onto the Tubes from both ends. Plug six Foam Roll End Caps (#26) into the ends. C.) Slide an Olympic S
Résumé du contenu de la page N° 12
STEP 6 (SEE DIAGRAM 6) A.) Attach the Arm Curl Pad (#18) to the Arm Curl Bracket (#45). Secure it with two M8 x 5/8” Allen Bolts (#39) and two Ø 5/8” Washers (#42). B.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#11). Insert the M10 x 3 5/8” Allen Bolt (#35) through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket then secure the Bolt with two Ø ¾” Washers (#41), and one M10 Aircraft Nut (#44). Do not over tighten the Nut and Bolt. The Bo
Résumé du contenu de la page N° 13
12
Résumé du contenu de la page N° 14
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Upright Beam 2 2 Rear Base Frame 1 3 Base Frame 2 4 Crutch 2 5 Main Seat Support 1 6 Rear Stabilizer 1 7 Leg Developer Holder 1 8 Backrest Support 2 9 Incline Support 1 10 Leg Developer 1 11 Arm Curl Stand 1 12 Incline Support Frame 2 13 Foam Tube 3 14 5 1/8” x 2 ¾” Bracket 1 15 5 ½” x 2” Bracket 2 16 Seat Pad 1 17 Backrest Board 1 18 Arm Curl Pad 1 19 M18 Lock Knob 2 20 Ø 5/8” Bushing 2 21 Ø 3” Sleeve 2 22 Ø 2 3/8” Sl
Résumé du contenu de la page N° 15
IMPEX INC . LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
