Instruction d'utilisation Impex Marcy Classic MCB-5693

Résumé du contenu de la page N° 1

NOTE:
Please read all instructions
carefully before using this
product




Table of Contents
MARCY CLASSIC

Safety Notice
WEIGHT BENCH


Hardware Identifier

MCB-5693
Assembly Instruction

Parts List

Warranty

Ordering Parts



Model
MCB-5693


Retain This
Manual for
Reference

07-23-08

OWNER'S
MANUAL

®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-f

Résumé du contenu de la page N° 2

TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 EXPLODED DIAGRAM…………………………………………………………………….. 10 PARTS L

Résumé du contenu de la page N° 3

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at

Résumé du contenu de la page N° 4

WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown 3

Résumé du contenu de la page N° 5

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4

Résumé du contenu de la page N° 6

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5

Résumé du contenu de la page N° 7

ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Plug four 2 ¾” x 2” End Cap (#21) onto the Left and Right Upright Beams (#1) & (#2). B.) Connect the Left and Right Upright Beams with a Cross Brace (#3) in the mid-span. Secure each end of the Cross Brace with two M10 x 2 ¾” Carriage Bolts (#42)

Résumé du contenu de la page N° 8

6 STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#4) to the Leg Developer Holder (#5). Secure it with two M10 x 2 ½” Carriage Bolts (#41), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts (#50). Do not tighten the Nuts and Bolts yet. B.) Attach the Main Seat Support to the Cross Brace (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#41), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts (#50). C.) Securely tighten all Nuts and Bolts. DIAGRAM 2 7

Résumé du contenu de la page N° 9

STEP 3 (See Diagram 3) A.) Attach the side-holes on the end of the Backrest Supports (#11) to the pivot on the Main Seat Support (#4). Secure them together with one M12 x 7 ¼” Hex Bolt (#43), two ∅ 1” Washers (#40) and one M12 Aircraft Nut (#51). B.) Attach the Backrest Board (#13) to the Backrest Supports. Secure it with four M8 x 1 ½” Allen Bolts (#47) and Ø 5/8” Washers (#38). Place the other end of Backrest Board rest against the Backrest Adjustment Bar. C.) Attach the two Seat B

Résumé du contenu de la page N° 10

8 STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#9) to the Leg Developer Holder (#5). Secure it with one Axle (#54), two M10 x 5/8” Allen Bolts (#45), and two ∅ ¾” Washers (#39). B.) Insert two Foam Tubes (#12) halfway through the holes on the Leg Developer. Push four Foam Rolls (#19) onto the Tubes from both ends. Plug four Foam Roll End Caps (#29) into the ends. C.) Slide an Olympic Sleeve (#28) onto the weight post on the Leg Developer. Attach a Spring Clip (#20) to the S

Résumé du contenu de la page N° 11

9

Résumé du contenu de la page N° 12

10 PARTS LIST KEY NO. DESCRIPTION Q’ty 46 M8 x 5/8” Allen Bolt 2 47 M8 x 1 ½” Allen Bolt 8 1 Left Upright Beam 1 48 M8 x 3 ½” Allen Bolt 1 2 Right Upright Beam 1 49 M8 Aircraft Nut 1 3 Cross Brace 1 50 M10 Aircraft Nut 10 4 Main Seat Support 1 51 M12 Aircraft Nut 1 5 Leg Developer Holder 1 52 ST2.9 Screw 4 6 Seat Bracket 2 53 Ø 2 3/8” Bushing 2 7 Crutch 2 54 Axle 1 8 Backrest Adjustment Bar 1 55 Ø 1” End Cap 1 9 Leg Developer 1 #5 Allen Wrench (Tool) 1 10 Ar

Résumé du contenu de la page N° 13

® IMPEX INC. LIMITED WARRANTY ®" IMPEX Inc. ("IMPEX ) warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling I