Résumé du contenu de la page N° 1
Operator’s manual (EPA I)
362XP
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
E E E En n n ng g g glllliiiis s s sh h h h
Résumé du contenu de la page N° 2
KEY TO SYMBOLS Protective goggles or a visor must be worn. Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or Refuelling. others. Please read the operator’s manual carefully and make sure you understand the Filing with oil and adjusting oil flow. instructions before using the machine. Always wear: • Approved protective helmet The chain brake must be engaged when the chain saw is started
Résumé du contenu de la page N° 3
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: .............................................. 2 Symbols in the operator’s manual: ................................ 2 CONTENTS Contents ....................................................................... 3 INTRODUCTION Dear customer! ............................................................. 4 WHAT IS WHAT? What is what on the chain saw? ................................... 5 GENERAL SAFETY PRECAUTIO
Résumé du contenu de la page N° 4
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot o
Résumé du contenu de la page N° 5
WHAT IS WHAT? Husqvarna XXX XXXX XXXXXXX Husqvarna AB Huskvarna, SWEDEN 6 8 5 27 3 4 2 1 22 7 1 9 21 11 10 19 18 16 14 13 20 24 17 15 25 23 26 What is what on the chain saw? 1 Cylinder cover 16 Bumper spike 2 Front handle 17 Chain catcher 3 Chain brake and front hand guard 18 Clutch cover 4 Starter 19 Rear handle with right hand guard 5 Chain oil tank 20 Throttle control 6 Starter handle 21 Throttle lock 7 Adjuster screws carburetor 22 Decompression valve 8 Choke control/Start throttle loc
Résumé du contenu de la page N° 6
GENERAL SAFETY PRECAUTIONS Before using a new chain saw Important • Please read this manual carefully. IMPORTANT! • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. The machine is only designed for cutting wood. • Refuel and start the chain saw. See the instructions under You should only use the saw with the bar and chain the headings Fuel Handling and Starting and Stopping. combinations we recommend in the chapter Te
Résumé du contenu de la page N° 7
GENERAL SAFETY PRECAUTIONS chain saw usage if possible. Your dealer, forestry school or • Fire Extinguisher and Shovel your library can provide information about which training materials and courses are available. Generally clothes should be close-fitting without restricting your freedom of movement. IMPORTANT! Sparks can come from the muffler, the bar and chain or other sources. Always have fire extinguishing tools available if you should need them. Help prevent forest fires.
Résumé du contenu de la page N° 8
GENERAL SAFETY PRECAUTIONS • The chain brake (A) can either be activated manually (by • To release the chain brake pull the front hand guard your left hand) or automatically by the inertia release backwards, towards the front handle. mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • Kickback can be very sudden and violent. Most kickbacks are minor and do not always activate the chain brake. If this happens you should hold the chain saw firmly and not
Résumé du contenu de la page N° 9
GENERAL SAFETY PRECAUTIONS • In the felling position the left hand is in a position that Throttle lock makes manual activation of the chain brake impossible. The throttle lock is designed to prevent accidental operation With this type of grip, that is when the left hand is placed of the throttle control. When you press the lock (A) (i.e. when so that it cannot affect the movement of the front hand you grasp the handle) it releases the throttle control (B). When gu
Résumé du contenu de la page N° 10
GENERAL SAFETY PRECAUTIONS The body of the chain saw, including the cutting equipment, is In areas with a hot, dry climate there is a high risk of fires. insulated from the handles by vibration damping units. These areas are sometimes subject to government rules requiring among other things the muffler must be equipped with an approved type of spark arrestor mesh. Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cut
Résumé du contenu de la page N° 11
GENERAL SAFETY PRECAUTIONS • Keep the chain properly tensioned! If the chain is slack Bar it is more likely to jump off and lead to increased wear on • Length (inches/cm) the bar, chain and drive sprocket. • Number of teeth on bar tip sprocket (T). • Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket. • Chain pitch (inches). The spacing bet
Résumé du contenu de la page N° 12
GENERAL SAFETY PRECAUTIONS It is very difficult to sharpen a chain correctly without the right Sharpening your chain and adjusting equipment. We recommend that you use our file gauge. This depth gauge setting will help you obtain the maximum kickback reduction and cutting performance from your chain. General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very sm
Résumé du contenu de la page N° 13
GENERAL SAFETY PRECAUTIONS General advice on adjusting depth gauge setting Tensioning the chain • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. WARNING! A slack chain may jump off the See instructions under the heading Technical data to find bar and cause serious or even fatal injury. the correct depth gauge setting for your part
Résumé du contenu de la page N° 14
GENERAL SAFETY PRECAUTIONS If the chain lubrication is not working: Lubricating cutting equipment • Check that the oil channel in the bar is not obstructed. Clean if necessary. WARNING! Poor lubrication of cutting equipment may cause the chain to snap, which ! could lead to serious, even fatal injuries. Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it • Check that the groove in the edge of the bar is clean. i
Résumé du contenu de la page N° 15
GENERAL SAFETY PRECAUTIONS • To prolong the life of the bar you should turn it over daily. Checking wear on cutting equipment Check the chain daily for: WARNING! Most chain saw accidents happen when the chain touches the ! operator. Wear personal protective equipment. See instructions under the heading Personal • Visible cracks in rivets and links. protective equipment. • Whether the chain is stiff. Do not tackle any job that you feel you are • Whether rivets and links are badly worn. not a
Résumé du contenu de la page N° 16
ASSEMBLY Tension the chain by turning the chain tensioning screw Fitting the bar and chain clockwise using the combination spanner. See instructions under the heading Tensioning the chain. WARNING! Always wear gloves, when working with the chain, in order to protect ! your hands from injury. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. The chain is correctly tensioned when it does not sag from the underside of the bar, but ca
Résumé du contenu de la page N° 17
FUEL HANDLING Mixing ratio Fuel 1:50 (2%) for all engines. Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two- Gasoline, litre Two-stroke oil, litre stroke oil. It is important to accurately measure the amount of 2% (1:50) oil to be mixed to ensure that the correct mixture is obtained. 5 0,10 When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. 10 0,43/0,20 15 0,30 WARNING! A
Résumé du contenu de la page N° 18
FUEL HANDLING • Never start the machine: Fueling 1 If you have spilt fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water. WARNING! Taking the following precautions, will lessen the risk of fire: 3 If the machine is leaking fuel. Check regularly for leaks ! from the fuel cap and fuel lines. Do no
Résumé du contenu de la page N° 19
STARTING AND STOPPING Warm engine Starting and stopping Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The WARNING! Note the following before correct choke/start throttle setting is obtained by moving the starting: ! choke control to the choke position and then pushing it in again. The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never st
Résumé du contenu de la page N° 20
STARTING AND STOPPING Note! Pull the front hand guard towards the front handle. The • Always hold the saw with both hands. The right hand chain brake is now disengaged. Your saw is ready for use. should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a firm grip with thumbs and fingers encircling the chain saw handles. WARNING! Long term inhalation of the engine’s exhaust fumes, chain oil mist and ! dust from s
