Résumé du contenu de la page N° 1
H5E-DV PC
H5EA PC
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, co
Résumé du contenu de la page N° 2
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year labor. 4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 po
Résumé du contenu de la page N° 3
INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the dispense valve that indicates the status of the dispenser. This equipment is for indoor use, either wall-mounted or on a sturdy counter or shelf. USER NOTICES The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. ! WARNING Very Hot Water Use With Care! 37881.0000 12593.0000 This equipment must be installed to comply 12
Résumé du contenu de la page N° 4
ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements. BLK RED L2 L1 120V. A.C. 200 or 230V. A.C. WHI RED L2 N 208 or 240V. A.C. 120V. A.C. BLK L1 GREEN GREEN P1842 Earth Ground Chassis Ground 120/208 & 120/240V ac 230V ac single phase models single phase models Note: This electrical service Note:
Résumé du contenu de la page N° 5
CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation. • An electrician must provide electrical service as specified in conformance with all local and national codes • This appliance must not be cleaned by water jet. • This appliance is not intended for use by persons (inclu
Résumé du contenu de la page N° 6
INITIAL SET-UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper panel from the rear of the dispenser. 2. Make sure the toggle switch below the circuit board is set to the desired voltage (120 volts or 208/240 volts) and the red switch on the circuit board is in the "SET" position. 3. Connect the dispenser to the power source and turn-on the water supply. 4. Place the master switch in
Résumé du contenu de la page N° 7
OPERATING CONTROLS d. c. a. b. P3743 e. (a) VOLUME SELECTOR BUTTONS Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress. (b) AUTO STOP/MANUAL DISPENSE BUTTON Press and release button to stop a dispense cycle. Press and hold button to dispense manually. (c) HIDDEN PROGRAMMING BUTTON (d) LED INDICATORS (e) DISPE
Résumé du contenu de la page N° 8
PROGRAMMING When power is applied to the dispenser, the display located on the bottom of the main circuit board will show the revision level of the software for 5 seconds, and then go to (-). While the tank is filling, the display will read (FIL). When the tank is full the display will return to (-). P3747 CENTER RIGHT LEFT BUTTON BUTTON BUTTON LEVEL 1 PROGRAMMING TANK WATER TEMPERATURE & READY TEMPERATURE SET-UP 1. Press and hold the center button until P1 appears on the display (approximat
Résumé du contenu de la page N° 9
3. Press and release the center button once more. The display will read H2, then show either FAH (Degrees in Fahrenheit) or Cen (Degrees in Centigrade). 4. Press and release the (+) or (-) buttons to alternate between FAH and CEn. 5. To Exit Level 2 Programming, press and release the Center Button twice more. The Display will show the Software Version, then (-). RESTORING FACTORY DEFAULTS 1. To restore Factory Defaults (This clears all settings that were previously entered), press and release
Résumé du contenu de la page N° 10
WIRING DIAGRAMS SCHEMATIC WIRING DIAGRAM H5E-DV PC GRN L1 N L2 BLK-14 RED-14 WHT-18 WHT-14 MASTER ON/OFF SWITCH RED-14 BLK-18 SELECTOR LIMIT SWITCH TANK HEATER THERMOSTAT BRN-14 BLU-14 BLK-14 BLK-14 4000 W TANK HEATER WHI/VIO-14 WHT-14 1800 W N.C. DISPENSE OVERFLOW WHT-18 SOL PROTECTION SWITCH REFILL WHT-18 SOL BLK-18 J5-1 J7-1 VIO-18 WHI-18 J5-3 WHI/BLU-18 J7-4 J2-1 BLK J4-1 WATER LEVEL WHI PROBE PINK-22 J6-1 J2-5 GRN-18 TANK MAIN t° CONTROL PANEL ASSY CONTROL Touch Switch Assembly Codes J1-1
Résumé du contenu de la page N° 11
WIRING DIAGRAMS SCHEMATIC WIRING DIAGRAM L1 L2 H5EA PC CE RED-14 BLK-14 GRN/YEL EMI FILTER RED-14 BLK-18 LIMIT LIMIT THERMOSTAT THERMOSTAT TANK HEATER RED-14 BLU-14 BLU-14 BLK-14 BLK-14 4000 W BLK BLK N.C. DISPENSE OVERFLOW RED-18 PROTECTION SWITCH SOL REFILL RED-18 SOL BLK-18 J5-3 J7-1 VIO-18 WHI-18 J5-1 WHI/BLU-18 J7-4 J2-10 BLK J4-1 WHI WATER LEVEL PINK-22 PROBE J6-1 GRN-18 TANK J2-5 MAIN t° CONTROL PANEL ASSY CONTROL Touch Switch Assembly Codes J1-1 BOARD A1 Left Dispense J2-1 STATIC A2 Mid
