Résumé du contenu de la page N° 1
MODEL W1758
VARIABLE SPEED WOOD LATHE
WITH DIGITAL READOUT
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED APRIL, 2010 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. (FOR MODELS MANUFACTURED SINCE 3/10)
#9397TS Printed in China
Résumé du contenu de la page N° 2
This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installa- tion in a safe environment, personnel training and usag
Résumé du contenu de la page N° 3
INTRODUCTION SAFETY ELECTRICAL SET UP OPERATIONS MAINTENANCE SERVICE PARTS Contents INTRODUCTION ...................................... 2 ACCESSORIES ....................................... 26 Woodstock Technical Support ..................2 Wood Lathe Accessories ....................... 26 SAFETY ................................................ 6 MAINTENANCE ..................................... 27 Standard Safety Instructions ...................6 General ........................................
Résumé du contenu de la page N° 4
W1758 Owner's Manual (Mfg. Since 3/10) INTRODUCTION Woodstock Technical Support This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. We s
Résumé du contenu de la page N° 5
INTRODUCTION W1758 Owner's Manual (Mfg. Since 3/10) MACHINE SPECIFICATIONS Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz MOdEl W1758 VARIABlE SPEEd WOOd lATHE WITH dIGITAl REAdOUT Motor Type ..........................................................................................TEFC Capacitor Start Induction Horsepower ................................................................................................................. 2 HP Voltage
Résumé du contenu de la page N° 6
W1758 Owner's Manual (Mfg. Since 3/10) Construction Materials Bed ................................................................................................ Precision Ground Cast Iron Legs .....................................................................................................................Cast Iron Headstock ..............................................................................................................Cast Iron Tool Rest ......................................
Résumé du contenu de la page N° 7
INTRODUCTION W1758 Owner's Manual (Mfg. Since 3/10) Controls and Features C J B I A K F G D H L E R P Q M O N A. Motor J. Quill Locking Lever B. Digital Readout K. Quill Handwheel C. Spindle L. Lathe Bed D. Spur Center M. Tool Rest Extension Locking Lever E. Speed Control Lever N. Tool Rest Base Locking Lever F. Tool Rest O. Tool Rest Locking Lever G. Tool Rest Base with Extension P. Headstock Rotation Locking Pin H. Tailstock Locking Lever Q. ON/OFF Switch with Lockout Key I. Live Center R. Hea
Résumé du contenu de la page N° 8
W1758 Owner's Manual (Mfg. Since 3/10) SAFETY READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. This symbol is used
Résumé du contenu de la page N° 9
SAFETY W1758 Owner's Manual (Mfg. Since 3/10) 10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended. 11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist. 12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents. 13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords
Résumé du contenu de la page N° 10
W1758 Owner's Manual (Mfg. Since 3/10) Additional Safety for Wood Lathes READ and understand this USE this and other machinery with caution entire instruction manual and respect. Always consider safety first, before using this lathe. as it applies to your individual working Serious personal injury conditions. No list of safety guidelines can may occur if safety and be complete—every shop environment is operational information is different. Failure to follow guidelines could not under
Résumé du contenu de la page N° 11
ELECTRICAL W1758 Owner's Manual (Mfg. Since 3/10) ELECTRICAL The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Test Run" portion of this manual. 110V Operation The Model W1758 is wired for 110V operation. We recom- mend connecting this machine to a dedicated circuit with Figure 1. NEMA 5-15 plug and receptacle. a verified ground, using the circuit size below as a mini- mum. Never replace a circui
Résumé du contenu de la page N° 12
W1758 Owner's Manual (Mfg. Since 3/10) SETUP Unpacking This machine has been carefully packaged for safe trans- portation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox A dealer immediately. C Inventory B The following is a description of the main components shipped with the Model W1758. Lay the components out E D to inventory them. Figure 2. Box 1 inventory. Note: If you can't find an item on this list, check the mounting location on t
Résumé du contenu de la page N° 13
SETUP W1758 Owner's Manual (Mfg. Since 3/10) Machine Placement Cleaning Machine • Floor Load: This lathe distributes a heavy The table and other unpainted parts of your load in a small footprint. Some residential machine type are coated with a waxy grease floors may require additional bracing to that protects them from corrosion during ship- support both machine and operator. ment. Clean this grease off with a solvent clean- er or citrus-based degreaser. DO NOT use chlo- • Working Clearances:
Résumé du contenu de la page N° 14
W1758 Owner's Manual (Mfg. Since 3/10) Mounting to Shop Floor Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hard- ware is not included. Generally, you can either bolt your machine to the floor or mount it on machine feet. Both options are described below. Whichever option you choose it will be necessary to use a precision level to level your machine. Bolting to Concrete Floors
Résumé du contenu de la page N° 15
SETUP W1758 Owner's Manual (Mfg. Since 3/10) 3. Using the 6mm hex wrench, secure the lathe to the legs with the eight cap screws and lock washers, as shown in Figure 8. 4. Install the handle into the tool rest, as shown in Figure 9. 5. Align the quill keyway with the entry hole of the quill lock lever (see Figure 10), then install the lever into the tailstock so that the end of it mates Figure 8. Securing lathe to legs. with the quill keyway. Note: Make sure the dog-end of the lock lever
Résumé du contenu de la page N° 16
Test Run W1758 Owner's Manual (Mfg. Since 3/10) Test Run Once the assembly is complete, test run your machine to Tie back long hair, roll make sure it runs properly and is ready for regular opera- up long sleeves, and tion. remove loose clothing, jewelry, or gloves to The test run consists of verifying the following: 1) The prevent getting caught motor powers up and runs correctly, and 2) the switch in moving parts. disabling mechanism works correctly. If, during the test run, you canno
Résumé du contenu de la page N° 17
OPERATIONS W1758 Owner's Manual (Mfg. Since 3/10) OPERATIONS General This lathe will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the under- standing that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine! READ
Résumé du contenu de la page N° 18
W1758 Owner's Manual (Mfg. Since 3/10) Adjusting Headstock The Model W1758 headstock can be positioned anywhere along the bed and swiveled 360°. To position the headstock along the length of the lathe bed, do these steps: 1. DISCONNECT THE LATHE FROM POWER! 2. Loosen the headstock locking lever (see Figure 13). 3. Position the headstock along the lathe bed and secure it in place by tightening the locking lever. Figure 13. Headstock locking lever. Note: The large clamping hex nut underneath
Résumé du contenu de la page N° 19
OPERATIONS W1758 Owner's Manual (Mfg. Since 3/10) Adjusting Tailstock The tailstock is equipped with a cam-action clamping sys- tem to secure it to the lathe bed. When the locking lever is tightened, a locking plate lifts up underneath the bed and secures the tailstock in place. To position the tailstock along the length of the bed, do these steps: 1. Loosen the tailstock locking lever (see Figure 15), and move the tailstock in position. Figure 15. Tailstock locking lever. 2. Re-tighten the
Résumé du contenu de la page N° 20
Headstock Center W1758 Owner's Manual (Mfg. Since 3/10) Installing/Removing Headstock Center Before beginning any turning opera- tion, make sure the headstock The included spur center installs into the headstock spin- and tailstock centers are properly dle with an MT#2 tapered fit. aligned. Refer to Aligning Headstock & Tailstock Centers on Page 28 for To install the headstock spur center, do these steps: instructions on this procedure. Failure to heed this warning could result in 1. DISC
