Résumé du contenu de la page N° 1
Model No. 831.153230
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
SEARS, ROEBUCK AND CO.,
HOFFMAN ESTATES, IL 60179
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
www.weiderfitness.com
this equipment. Save this manual
new products, prizes,
for future reference.
fitness tips, and much more!
Résumé du contenu de la page N° 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PART IDENTIFICATION CHART . . . . . . . .
Résumé du contenu de la page N° 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. 1. Read all instructions in this manual before 11. The weight bench is designed to support a using the weight bench. Use the weight maximum user weight of 250 pounds. Do not bench only as described in this manual. place more than 310 pounds, including the barbell, on the weight rests. Do not place 2. It is the responsibility of the owner to ensure more than
Résumé du contenu de la page N° 4
BEFORE YOU BEGIN ® Thank you for selecting the WEIDER PRO 575 weight HELPLINE at 1-800-736-6879, Monday through bench. The PRO 575 is designed to be used with your Saturday, 7 a.m. until 7 p.m. Central Time (excluding own weight set (not included) to develop every major holidays). To help us assist you, please note the prod- muscle group of the body. Whether your goal is a uct model number and serial number before calling. shapely figure, dramatic muscle size and strength, or a The model number
Résumé du contenu de la page N° 5
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. M10 x 57mm Bolt (78) M10 Nylon Locknut (77) M10 Washer (79) M10 x 62mm Carriage Bolt (74) M6 Locknut (80) M10 x 75mm Bolt (73) M6 Washer (62) M10 x 78mm
Résumé du contenu de la page N° 6
ASSEMBLY • As you assemble the weight bench, make sure all Make Things Easier for Yourself parts are oriented as shown in the drawings. Everything in this manual is designed to ensure • For help identifying small parts, use the PART that the weight bench can be assembled suc- IDENTIFICATION CHART on page 5. cessfully by anyone. However, it is important to realize that the versatile weight bench has many The following tools (not included) are required parts and that the assembly process will ta
Résumé du contenu de la page N° 7
2. Press two 50mm Thick Square Inner Caps (53) 2 1 and a 2” x 3” Inner Cap (50) into the ends of the 22 77 50 Center Base (24). Have a second person hold the Right and Left 77 90 Uprights (1, 2 [not shown]). Attach the Right and Left Bases (22, 23) to the Center Base (24) with two M10 x 97mm Bolts (90) and two M10 Nylon 53 Locknuts (77). Do not tighten the Nylon 23 Locknuts yet. 24 53 90 3. Press two 2” Round Inner Caps (47) into the ends 3 of the weight tube on the Weight Carriage (25). Press
Résumé du contenu de la page N° 8
6. Press two 75mm Bushings (26) into the top and 6 bottom of the Right Weight Rest (12). 26 30 Pull the Knob (30) out as far as it will go. Slide the Right Weight Rest (12) onto the Right Upright (2) 12 and snap the Knob into an adjustment hole in the Upright. Turn the Knob clockwise until tight. 26 Repeat this step with the Left Weight Rest (not shown). 2 7. Press two 60mm Square Inner Caps (46) into the 7 70 top of the Left and Right Uprights (1, 2). 46 Orient the Center Frame (4) with the d
Résumé du contenu de la page N° 9
10. Orient the Pull-up Bar (8) with the bend on top. 10 77 Attach the Pull-up Bar to the Right Frame (5) with two M10 x 57mm Bolts (78), two M10 Washers 79 79 5 (79), and two M10 Nylon Locknuts (77). Do not tighten the Nylon Locknuts yet. Attach the Pull-up Bar (8) to the Left Frame (not shown) in the same manner. Top Tighten the M10 Nylon Locknuts (77) used in 8 steps 1–10. 78 11. Press two 38mm x 50mm Inner Caps (52) into 11 52 the top of the Back Leg (39). Press two 50mm Square Inner Caps
Résumé du contenu de la page N° 10
14. Attach the Bench Frame (14) to the Back Leg 14 (39) with an M10 x 78mm Bolt (70), two M10 x 77 164mm Bolts (71), an M10 Washer (79), and three M10 Nylon Locknuts (77). Do not tighten 70 39 the Nylon Locknuts yet. 14 71 79 77 15. Attach the Leg Lever Bumper (54) to the Front 15 Leg (18) with the M4 x 19mm Screw (68) and an 50 77 M5 Washer (92). 49 Press a 38.1mm x 76.2mm Inner Cap (49) and a 19 2” x 3” Inner Cap (50) into the Leg Lever (19). 91 54 Lubricate an M10 x 102mm Bolt (91). Attach th
Résumé du contenu de la page N° 11
18. Press two 38mm Square Inner Caps (44) into the 18 ends of the Seat Frame (17). 37 Orient the Seat (37) with the wide end on the side Wide End shown. Attach the Seat (37) to the Seat Frame (17) with four M6 x 16mm Bolts (72). 44 17 44 72 72 19. Lubricate an M10 x 154mm Bolt (69). Attach the 19 Seat Frame (17) to the Backrest Frame (16) with the Bolt, two M10 Washers (79), and an M10 17 Nylon Locknut (77). Do not overtighten the Nylon Locknut; the Seat Frame must be able to pivot easily. 77 79
Résumé du contenu de la page N° 12
22. Route the Bench Cable (58) under a 4 1/2” Pulley 22 (35). Attach the Pulley to the Front Leg (18) with an M10 x 75mm Bolt (73), two 17mm Spacers (96), two M10 Washers (79), and an M10 Nylon Locknut (77). 96 35 77 58 79 96 18 79 73 23. Attach the Bench Cable (58) to the Back Leg (39) 23 with a Cable Clip (28). 39 28 58 24. Press a 19mm Round Inner Cap (48) into each 24 end of the three Pad Tubes (41). 42 Slide two Pad Tubes (41) through the holes in the 42 Leg Lever (19). Slide the third Pad
Résumé du contenu de la page N° 13
26. Wrap the High Cable (61) around an 88mm 26 Pulley (36). Attach the Pulley and a Small Cable 77 Trap (93) to the Left Frame (6) with an M10 x 45mm Bolt (76) and an M10 Nylon Locknut (77). 93 36 76 6 61 27. Wrap the High Cable (61) around a 4 1/2” Pulley 27 (35). Attach the Pulley and a Large Cable Trap (55) to the “U”-Bracket (33) with an M10 x 45mm 61 35 Bolt (76) and an M10 Nylon Locknut (77). 55 77 76 33 28. Wrap the High Cable (61) around an 88mm 28 76 Pulley (36). Attach the Pulley and a
Résumé du contenu de la page N° 14
31. Wrap the Carriage Cable (60) around a 4 1/2” 31 Pulley (35). Attach the Pulley and a Large Cable Trap (55) to the single set of holes in the pair of 60 Pulley Plates (31) with an M10 x 45mm Bolt (76) and an M10 Nylon Locknut (77). 35 77 76 55 31 32. Wrap the Carriage Cable (60) around an 88mm 32 79 9 Pulley (36). Attach the Pulley inside the Top 96 77 Frame (9) with an M10 x 75mm Bolt (73), two 17mm Spacers (96), two M10 Washers (79), and an M10 Nylon Locknut (77). 79 73 96 36 60 33. Wrap th
Résumé du contenu de la page N° 15
35. Locate the Low Cable (59). Lay the Cable inside 35 the bracket on the Center Base (24) so that the ball is on the side shown. Attach a 4 1/2” Pulley (35) inside the bracket with an M10 x 45mm Bolt 35 (76) and an M10 Nylon Locknut (77). 77 Ball 59 24 76 Bracket 36. Route the Low Cable (59) through the Center 36 Upright (3) and under the bar in the bracket on the 59 Center Base (24). Wrap the Cable around an 88mm Pulley (36). Attach the Pulley to the rear 36 77 hole in the bracket on the Cente
Résumé du contenu de la page N° 16
39. Attach the Low Cable (59) to the “U”-Bracket (33) 39 with an M6 Washers (62) and an M6 Locknut (80). Do not completely tighten the Locknut; it should be threaded onto the end of the Cable until only two threads are showing above the Locknut, as shown in the inset drawing. 33 80 62 80 59 59 33 40. Make sure all parts of the weight bench are properly tightened. In addition, pull each cable a few times to make sure the cables move smoothly over the pulleys. If the cables do not move smoothly, l
Résumé du contenu de la page N° 17
ADJUSTMENTS This section explains how to adjust the weight bench. The first time you perform an exercise that uses the safety spotter, adjust the bench to the position that is best for you. Note the position of the weight rest and safety spot- ter on the BENCH ADJUSTMENT CHART, on page 20 of this manual. When preparing to perform the exercise again, refer back to the chart for a quick reference to your personal settings. See the EXERCISE GUIDELINES on page 21 for important information about how
Résumé du contenu de la page N° 18
ATTACHING THE BENCH TO THE RACK To perform bench and leg lever exercises, the weight bench must be attached to the weight rack. To attach the bench to the rack, rest the Back Leg (39) over the crossbar on the Center Base (24). Note: Be sure that the Low Cable (59) goes through the Back 39 Leg. Next, attach the Bench Cable (58) to the Low Cable with a Cable Clip (28). When the bench is not attached to the rack, use the Cable Clip (28) to attach the Bench Cable (58) to the bracket on the Back Leg
Résumé du contenu de la page N° 19
USING THE POWER ASSIST LEGS 20 If you are unable to complete the repetition after per- forming a bench exercise, the Power Assist Legs (20, 21) can be used to help lift the barbell back to the Weight Rests (not shown). To use the Power Assist Legs (20, 21), attach the bench to the rack and a barbell to the high cable (see 21 ATTACHING THE BENCH TO THE RACK and ATTACHING A BARBELL TO THE CABLES on page 18). Press down on the Power Assist Legs with your feet while lifting the barbell to the Weight
Résumé du contenu de la page N° 20
BENCH ADJUSTMENT CHART The chart below contains a list of exercises that require the use of the safety spotter. When preparing the weight bench for one of these exercises, follow the steps listed below. For information about each of these steps, refer to the ADJUSTMENTS section of this manual. Make sure the bench cable is attached to the low cable when performing any of the bench exercises. For each exercise, determine the positions of the bench, the weight rests, and the safety spotter that are
